Sharp MX 4501N Installation Manual - Page 9

Little, Moderate, amount, Cleaner UN

Get Sharp MX 4501N - Color Laser - All-in-One PDF manuals and user guides View all Sharp MX 4501N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

4 : Nov. 15 2006 4 4) Rotate the belt by amount 10 cm to move the application part to the surface. * Till the applied powder reaches the cleaner installation location. (Application amount) 5) Mount the cleaner frame UN on the primary transfer UN. 6) Apply titanium hydroxide to the belt. * Apply titanium hydroxide to the belt 40 times (10 times in latitudinal direction x 4 times in longitudinal direction) for 4 faces (making two circuits of the belt). * Repeat half-around application and half-around rotation each 4 times. * Apply titanium hydroxide not to produce bias. Little Moderate amount Much 7) Face the primary transfer UN upward. * Face the primary transfer UN UPward from the cleaner UN side. * Take care that powders will not fly apart. Cleaner UN 8) Mount the primary transfer UN on the machine and execute simulation 25-1 (3-minute belt idling) once. 9) Check omissions in characters, and if many omissions are found, execute simulation 25-1 once again. 10) If titanium hydroxide flies apart near the resist roller, clean it. MX-3500N/4500N, MX-3501N/4501N 1 - 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
MX-3500N/4500N, MX-3501N/4501N
1 – 6
4)
Rotate the belt by amount 10 cm to move the application part
to the surface.
*
Till the applied powder reaches the cleaner installation loca-
tion.
5)
Mount the cleaner frame UN on the primary transfer UN.
6)
Apply titanium hydroxide to the belt.
*
Apply titanium hydroxide to the belt 40 times (10 times in lat-
itudinal direction x 4 times in longitudinal direction) for
4 faces (making two circuits of the belt).
*
Repeat half-around application and half-around rotation
each 4 times.
*
Apply titanium hydroxide not to produce bias.
(Application amount)
7)
Face the primary transfer UN upward.
*
Face the primary transfer UN UPward from the cleaner UN
side.
*
Take care that powders will not fly apart.
8)
Mount the primary transfer UN on the machine and execute
simulation 25-1 (3-minute belt idling) once.
9)
Check omissions in characters, and if many omissions are
found, execute simulation 25-1 once again.
10)
If titanium hydroxide flies apart near the resist roller, clean it.
4
Little
Moderate
amount
Much
Cleaner UN
: Nov. 15 2006
4