Sony DPP-FP50 Operating Instructions - Page 16

Preparing the, remote commander

Get Sony DPP-FP50 - Picture Station Digital Photo Printer PDF manuals and user guides
UPC - 027242678583
View all Sony DPP-FP50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

5 Preparing the remote commander 1 Remove the insulation sheet from the remote commander. With the insulation sheet removed from the lithium battery, the remote commander is ready for use. Replacing batteries When the printer does not respond to the remote commander, the battery may run out. 1 Push in the tab (1) and then slide out the battery compartment lid (2). 2 Remove the used battery and then insert a new lithium battery (CR2025) into the compartment with the + and - properly aligned. Friction seal 2 Point the remote commander to the remote sensor on the printer and then press a button to operate the printer. You can use the buttons on the remote commander in the same way as those identical buttons on the printer. Lithium battery Remote sensor Note Pressing CANCEL button on a remote commander for more than one second does not function. 3 Slide the battery compartment lid back into the commander until it clicks into place. WARNING: Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire. Notes • The button-type battery CR2025 is used in the remote commander. Do not use a battery other than the CR2025. • Point the remote sensor away from strong light sources such as direct sunlight or overhead lighting. Otherwise, the remote commander may not function properly. 16 GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
16
GB
5
Preparing the
remote commander
1
Remove the insulation sheet from
the remote commander.
With the insulation sheet removed
from the lithium battery, the remote
commander is ready for use.
Friction seal
2
Point the remote commander to
the remote sensor on the printer
and then press a button to
operate the printer.
You can use the buttons on the remote
commander in the same way as those
identical buttons on the printer.
Remote sensor
Replacing batteries
When the printer does not respond to the
remote commander, the battery may run
out.
1
Push in the tab (
1
) and then slide
out the battery compartment lid
(
2
).
2
Remove the used battery and
then insert a new lithium battery
(CR2025) into the compartment
with the + and – properly aligned.
Lithium battery
3
Slide the battery compartment lid
back into the commander until it
clicks into place.
WARNING:
Battery may explode if mistreated.
Do not
recharge, disassemble or dispose of in fire.
Notes
•
The button-type battery CR2025 is used in the
remote commander.
Do not use a battery
other than the CR2025.
•
Point the remote sensor away from strong
light sources such as direct sunlight or
overhead lighting.
Otherwise, the remote
commander may not function properly.
Note
Pressing CANCEL button on a remote
commander for more than one second does not
function.