Home » Stihl Manuals » Lawn & Garden » Stihl MS 162 » Manual Viewer

Stihl MS 162 Instruction Manual - Page 33

Starting the Engine

Get Stihl MS 162 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

14 Starting the Engine English ► While maintaining steady, downward pressure, slowly turn the cap approximately a 1/2 turn counter-clockwise. ► If any significant venting occurs, immediately re-seal the tank by turning the cap clockwise to the closed position. Allow the chain saw to cool further before attempting to open the tank. ► Remove the fuel filler cap and fill the tank with fuel. ► Take care not to spill fuel while refilling the tank. ► Do not overfill the tank. Leave approximately 0.5 in. (13 mm) of air space. Closing To close the tank: 0000097426_001 ► Position the cap on the tank filler neck and press it down while turning it clockwise by hand until it is secure. ► Check for tightness. ► If your fuel cap still does not tighten properly, it may be damaged or broken. Stop using the chain saw and take it to your authorized STIHL dealer for repair. 14 Starting the Engine 14.1 Holding the Chain Saw A B C 0000-GXX-2936-A2 ► When starting, hold the chain saw firmly in one of three ways: - Position the chain saw on a level surface. Hold the saw firmly on the ground with your left hand on the front handle. Your thumb should be under the handle. Put the toe of your right boot into the rear handle and press down (Illustration A). - Position the chain saw on a level surface. Hold the saw firmly on the ground with your left hand on the front handle. Your thumb should be under the handle. Put the heel of your right boot onto the rear hand guard and press down (Illustration B). - Hold the saw firmly with your left hand on the front handle. Your thumb should be under the handle. Hold the rear handle tightly between your legs, just above the knees (Illustration C). 14.2 Starting Procedure Pre-Starting Procedure Follow the pre-starting procedure if one of the following applies: - The engine has not been started and is cold. - The engine started, but shut off when it was accelerated the first time. - The engine shut off because the fuel tank ran dry. When can the engine be started without the prestarting procedure? The engine can be started without preparation if it has been running for at least 1 minute and was only shut off for a short work break. ► Continue to Starting the Engine, 14.4. 14.3 Pre-Starting Procedure To perform the pre-starting procedure: 2 5 0000097427_001 1 4 3 ► Engage the chain brake (2), 12.1. ► If the chain saw is equipped with a manual fuel pump (1): Depress the manual fuel pump at least 10 times. ► Press down the throttle trigger lockout (5) and squeeze the throttle trigger (4) at the same time. ► Set the Master Control Lever (3) to position . ► Hold the chain saw firmly and pull the starter grip slowly with your right hand until you feel it engage. 0458-200-8621-A 33

Section	Page
STIHL MS 162, 172	1
1 Introduction	2
2 Guide to Using this Manual	2
2.1 Signal Words	2
2.2 Symbols in Text	2
3 Main Parts	3
3.1 Chain Saw	3
3.2 Optional Features	4
4 Safety Symbols on the Product	4
4.1 Chain Saw	4
5 IMPORTANT SAFETY INSTRUCTIONS	4
5.1 Intended Use	4
5.2 Operator	4
5.3 Personal Protective Equipment	5
5.4 Chain Saw	6
5.5 Fueling Instructions	7
5.6 Using the Chain Saw	9
6 Kickback and Other Reactive Forces	14
6.1 Reactive Forces	14
6.2 Kickback	14
6.3 Pull-in	18
6.4 Pushback	18
7 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling	18
7.1 Bucking	18
7.2 Cutting Logs Under Tension	19
7.3 Limbing	20
7.4 Pruning	20
7.5 Felling	21
8 Maintenance, Repair and Storage	24
8.1 Warnings and Instructions	24
9 Before Starting Work	25
9.1 Preparing the Chain Saw for Operation	25
10 Assembling the Chain Saw	25
10.1 Cutting Attachment	25
10.2 Mounting and Removing the Guide Bar and Chain	25
10.3 Tensioning the Saw Chain	28
11 Lubricating the Saw Chain and Guide Bar	29
11.1 Bar and Chain Lubricant	29
11.2 Filling the Chain Oil Tank	29
12 The Chain Brake	30
12.1 Engaging the Chain Brake	30
12.2 Disengaging the Chain Brake	30
12.3 Maintaining the Chain Brake	30
13 Mixing Fuel and Refueling the Chain Saw	31
13.1 Mixing Fuel	31
13.2 Refueling the Chain Saw	32
14 Starting the Engine	33
14.1 Holding the Chain Saw	33
14.2 Starting Procedure	33
14.3 Pre-Starting Procedure	33
14.4 Starting the Engine	34
15 Shutting Off the Engine	34
15.1 Shutting Off the Engine	34
16 Checking the Chain Saw	35
16.1 Checking the Operation of the Chain Brake	35
16.2 Testing the Controls	35
16.3 Testing Chain Lubrication	35
17 After Finishing Work	36
17.1 Preparing for Transportation or Storage	36
18 Transporting	36
18.1 Transporting the Chain Saw	36
19 Storing	36
19.1 Storing the Chain Saw	36
20 Cleaning	37
20.1 Cleaning the Chain Saw	37
20.2 Cleaning the Guide Bar and Saw Chain	37
20.3 Cleaning the Air Filter	37
20.4 Cleaning the Spark Plug	38
21 Inspection and Maintenance	39
21.1 Inspection and Maintenance Chart	39
21.2 Inspecting and Maintaining the Chain Saw	40
21.3 Inspecting and Maintaining the Chain Sprocket	40
21.4 Inspecting and Maintaining the Guide Bar	40
21.5 Inspecting, Maintaining and Sharpening the Saw Chain	41
22 Troubleshooting Guide	43
22.1 Chain saw	43
22.2 Adjusting Idle Speed	44
22.3 Clearing the Combustion Chamber	44
23 Specifications	45
23.1 EPA	45
23.2 STIHL MS 162, 172	45
23.3 Chain Sprockets	45
23.4 Minimum Groove Depth of Guide Bars	45
23.5 Depth Gauge Setting	45
23.6 Symbols on the Chain Saw	45
23.7 Engineering Improvements	46
24 Combinations of Guide Bars and Saw Chains	46
24.1 STIHL MS 162, MS 172	46
25 Replacement Parts and Equipment	48
25.1 Genuine STIHL Replacement Parts	48
26 Disposal	48
26.1 Disposal of the Power Tool	48
27 Limited Warranty	48
27.1 STIHL Incorporated Limited Warranty Policy	48
28 Emission Control Warranty	48
28.1 STIHL Incorporated Federal Emission Control Warranty Statement	48
29 Trademarks	50
29.1 Registered Trademarks	50
29.2 Common Law Trademarks	50
30 Addresses	50
30.1 STIHL Incorporated	50
1 Introducción	51
2 Acerca de este manual de instrucciones	51
2.1 Palabras identificadoras	51
2.2 Símbolos en el texto	51
3 Componentes importantes	52
3.1 Motosierra	52
3.2 Características opcionales	53
4 Símbolos de seguridad en el producto	53
4.1 Motosierra	53
5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD	53
5.1 Uso previsto	53
5.2 Operador	54
5.3 Equipos de protección personal	54
5.4 Motosierra	55
5.5 Instrucciones para el llenado de combustible	56
5.6 Uso de la motosierra	59
6 Contragolpe y otras fuerzas reactivas	65
6.1 Fuerzas reactivas	65
6.2 Contragolpe	65
6.3 Tirones	69
6.4 Rechazo	69
7 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos	70
7.1 Tronzado	70
7.2 Corte de troncos bajo tensión	71
7.3 Desrame	71
7.4 Poda	72
7.5 Tala	72
8 Mantenimiento, reparación y almacenamiento	76
8.1 Advertencias e instrucciones	76
9 Antes de empezar a trabajar	77
9.1 Preparación de la motosierra para el funcionamiento	77
10 Armado de la motosierra	77
10.1 Accesorio de corte	77
10.2 Montaje y retiro de la espada y la cadena de aserrado	77
10.3 Tensado de la cadena de sierra	80
11 Lubricación de la cadena de aserrado y de la espada	81
11.1 Lubricante de espadas y cadenas	81
11.2 Llenado del depósito de aceite de la cadena	81
12 El freno de cadena	82
12.1 Accionamiento del freno de la cadena	82
12.2 Cómo soltar el freno de la cadena	83
12.3 Mantenimiento del freno de la cadena	83
13 Mezcla del combustible y carga de combustible en la motosierra	83
13.1 Mezcla del combustible	83
13.2 Recarga de combustible de la motosierra	85
14 Arranque del motor	86
14.1 Sujeción de la motosierra	86
14.2 Procedimiento de arranque	86
14.3 Procedimiento de prearranque	87
14.4 Arranque del motor	87
15 Apagado del motor	88
15.1 Apagado del motor	88
16 Revisión de la motosierra	88
16.1 Control del funcionamiento del freno de la cadena	88
16.2 Prueba de los controles	88
16.3 Prueba de la lubricación de la cadena	89
17 Después de completar el trabajo	89
17.1 Preparación para el transporte o el almacenamiento	89
18 Transporte	89
18.1 Transporte de la motosierra	89
19 Almacenamiento	90
19.1 Almacenamiento de la motosierra	90
20 Limpieza	90
20.1 Limpieza de la motosierra	90
20.2 Limpieza de la barra guía y la cadena de sierra	91
20.3 Limpieza del filtro de aire	91
20.4 Limpieza de la bujía	92
21 Inspección y mantenimiento	93
21.1 Tabla de inspección y mantenimiento	93
21.2 Inspección y mantenimiento de la motosierra	94
21.3 Inspección y mantenimiento del piñón de la cadena	94
21.4 Inspección y mantenimiento de la espada	94
21.5 Inspección, mantenimiento y afilado de la cadena de aserrado	95
22 Guía de solución de problemas	97
22.1 Motosierra	97
22.2 Ajuste de la velocidad de marcha en vacío	98
22.3 Desobstrucción de la cámara de combustión	99
23 Especificaciones	99
23.1 E.P.A.	99
23.2 STIHL MS 162, 172	99
23.3 Piñones de la cadena	100
23.4 Profundidad mínima de ranura de las barras guía	100
23.5 Ajuste del calibrador de profundidad	100
23.6 Símbolos en la motosierra	100
23.7 Mejoramientos técnicos	100
24 Combinaciones de espadas y cadenas de aserrado	101
24.1 STIHL MS 162, MS 172	101
25 Piezas y equipos de repuesto	102
25.1 Piezas de repuesto originales de STIHL	102
26 Eliminación	102
26.1 Desecho de la herramienta motorizada	102
27 Garantía limitada	103
27.1 Política de garantía limitada de STIHL Incorporated	103
28 Garantía del sistema de control de emisiones	103
28.1 Declaración de garantía de STIHL Incorporated sobre sistemas de control de emisiones según normas federales	103
29 Marcas comerciales	105
29.1 Marcas comerciales registradas	105
29.2 Marcas comerciales por ley común	105
30 Direcciones	105

Match case Limit results 1 per page

►

While maintaining steady, downward pressure,

slowly turn the cap approximately a 1/2 turn

counter-clockwise.

►

If any significant venting occurs, immediately

re-seal the tank by turning the cap clockwise

to the closed position. Allow the chain saw to

cool further before attempting to open the

tank.

►

Remove the fuel filler cap and fill the tank with

fuel.

►

Take care not to spill fuel while refilling the

tank.

►

Do not overfill the tank. Leave approximately

0.5 in. (13 mm) of air space.

Closing

To close the tank:

0000097426_001

►

Position the cap on the tank filler neck and

press it down while turning it clockwise by

hand until it is secure.

►

Check for tightness.

►

If your fuel cap still does not tighten properly, it

may be damaged or broken. Stop using the

chain saw and take it to your authorized

STIHL dealer for repair.

Starting the Engine

14.1

Holding the Chain Saw

0000-GXX-2936-A2

►

When starting, hold the chain saw firmly in one

of three ways:

–

Position the chain saw on a level surface.

Hold the saw firmly on the ground with your

left hand on the front handle. Your thumb

should be under the handle. Put the toe of

your right boot into the rear handle and

press down (Illustration A).

–

Position the chain saw on a level surface.

Hold the saw firmly on the ground with your

left hand on the front handle. Your thumb

should be under the handle. Put the heel of

your right boot onto the rear hand guard and

press down (Illustration B).

–

Hold the saw firmly with your left hand on

the front handle. Your thumb should be

under the handle. Hold the rear handle

tightly between your legs, just above the

knees (Illustration C).

14.2

Starting Procedure

Pre-Starting Procedure

Follow the pre-starting procedure if one of the

following applies:

–

The engine has not been started and is cold.

–

The engine started, but shut off when it was

accelerated the first time.

–

The engine shut off because the fuel tank ran

dry.

When can the engine be started without the pre-

starting procedure?

The engine can be started without preparation if

it has been running for at least 1 minute and was

only shut off for a short work break.

►

Continue to Starting the Engine,

14.4.

14.3

Pre-Starting Procedure

To perform the pre-starting procedure:

0000097427_001

►

Engage the chain brake (2),

12.1.

►

If the chain saw is equipped with a manual fuel

pump (1): Depress the manual fuel pump at

least 10 times.

►

Press down the throttle trigger lockout (5) and

squeeze the throttle trigger (4) at the same

time.

►

Set the Master Control Lever (3) to position

►

Hold the chain saw firmly and pull the starter

grip slowly with your right hand until you feel it

engage.

14 Starting the Engine

English

0458-200-8621-A