Home » TP-Link Manuals » Hubs & Switches » TP-Link 10GE » Manual Viewer

TP-Link 10GE T1700G-28TQUN V1 User Guide - Page 65

LAG

Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Select: Port: Status: Operation Mode: Recovery Mode: Loop Status: Block Status: LAG: Recover: Select the desired port for Loopback Detection configuration. It is multi-optional. Displays the port number. Enable or disable Loopback Detection function for the port. Select the mode how the switch processes the detected loops.  Alert: When a loop is detected, display an alert.  Port based: When a loop is detected, display an alert and block the port. Select the mode how the blocked port recovers to normal status.  Auto: Block status can be automatically removed after recovery time.  Manual: Block status only can be removed manually. Displays the port status whether a loopback is detected. Displays the port status about block or unblock. Displays the LAG number the port belongs to. Click the Recover button to manually remove the block status of selected ports. Note: Loopback Detection must coordinate with storm control. 6.2 LAG LAG (Link Aggregation Group) is to combine a number of ports together to make a single high-bandwidth data path, so as to implement the traffic load sharing among the member ports in the group and to enhance the connection reliability. For the member ports in an aggregation group, their basic configuration must be the same. The basic configuration includes STP, QoS, VLAN, port attributes, MAC Address Learning mode and other associated settings. More details are explained below:  If the ports, which are enabled for the 802.1Q VLAN, STP, QoS and Port Configuration (Speed and Flow Control), are in a LAG, their configurations would be the same as the LAG's.  The ports, which are enabled for the half-duplex, Port Security, Port Mirror and MAC Address Filtering, cannot be added to the LAG. If the LAG is needed, you are suggested to configure the LAG function here before configuring the other functions for the member ports. Tips: 1. Calculate the bandwidth for a LAG: If a LAG consists of the four ports in the speed of 1000Mbps Full Duplex, the whole bandwidth of the LAG is up to 8000Mbps (2000Mbps * 4) because the bandwidth of each member port is 2000Mbps counting the up-linked speed of 1000Mbps and the down-linked speed of 1000Mbps. 55

Section	Page
Package Contents	11
Chapter 1 About this Guide	12
1.1 Intended Readers	12
1.2 Conventions	12
1.3 Overview of This Guide	12
Chapter 2 Introduction	16
2.1 Overview of the Switch	16
2.2 Appearance Description	16
2.2.1 Front Panel	16
2.2.2 Rear Panel	17
Chapter 3 Login to the Switch	19
3.1 Login	19
3.2 Configuration	20
Chapter 4 System	21
4.1 System Info	21
4.1.1 System Summary	21
4.1.2 Device Description	24
4.1.3 System Time	24
4.1.4 Daylight Saving Time	25
4.2 User Management	26
4.2.1 User Table	26
4.2.2 User Config	27
4.3 System Tools	28
4.3.1 Boot Config	28
4.3.2 Config Restore	29
4.3.3 Config Backup	30
4.3.4 Firmware Upgrade	31
4.3.5 System Reboot	31
4.3.6 System Reset	32
4.4 Access Security	32
4.4.1 Access Control	32
4.4.2 HTTP Config	34
4.4.3 HTTPS Config	34
4.4.4 SSH Config	37
4.4.5 Telnet Config	44
4.5 SDM Template	44
4.5.1 SDM Template Config	44
Chapter 5 Stack	46
5.1 Stack Management	53
5.1.1 Stack Info	53
5.1.2 Stack Config	54
5.2 Application Example for Stack	56
Chapter 6 Switching	57
6.1 Port	57
6.1.1 Port Config	57
6.1.2 Port Mirror	58
6.1.3 Port Security	60
6.1.4 Port Isolation	62
6.1.5 Loopback Detection	63
6.2 LAG	65
6.2.1 LAG Table	66
6.2.2 Static LAG	67
6.2.3 LACP Config	68
6.3 Traffic Monitor	70
6.3.1 Traffic Summary	70
6.3.2 Traffic Statistics	71
6.4 MAC Address	73
6.4.1 Address Table	74
6.4.2 Static Address	75
6.4.3 Dynamic Address	76
6.4.4 Filtering Address	78
Chapter 7 VLAN	80
7.1 802.1Q VLAN	81
7.1.1 VLAN Config	82
7.1.2 Port Config	83
7.2 Application Example for 802.1Q VLAN	85
7.3 MAC VLAN	86
7.3.1 MAC VLAN	87
7.3.2 Port Enable	87
7.4 Application Example for MAC VLAN	88
7.5 Protocol VLAN	90
7.5.1 Protocol Group Table	91
7.5.2 Protocol Group	91
7.5.3 Protocol Template	92
7.6 Application Example for Protocol VLAN	94
Chapter 8 Spanning Tree	96
8.1 STP Config	101
8.1.1 STP Config	101
8.1.2 STP Summary	103
8.2 Port Config	104
8.3 MSTP Instance	105
8.3.1 Region Config	106
8.3.2 Instance Config	106
8.3.3 Instance Port Config	107
8.4 STP Security	109
8.4.1 Port Protect	109
8.4.2 TC Protect	112
8.5 Application Example for STP Function	112
Chapter 9 Multicast	117
9.1 IGMP Snooping	121
9.1.1 Snooping Config	123
9.1.2 Port Config	125
9.1.3 VLAN Config	126
9.1.4 Multicast VLAN	127
9.1.5 Querier Config	130
9.1.6 Profile Config	132
9.1.7 Profile Binding	133
9.1.8 Packet Statistics	135
9.2 MLD Snooping	136
9.2.1 Snooping Config	138
9.2.2 Port Config	140
9.2.3 VLAN Config	141
9.2.4 Multicast VLAN	142
9.2.5 Querier Config	143
9.2.6 Profile Config	145
9.2.7 Profile Binding	146
9.2.8 Packet Statistics	148
9.3 Multicast Table	149
9.3.1 IPv4 Multicast Table	149
9.3.2 Static IPv4 Multicast Table	150
9.3.3 IPv6 Multicast Table	151
9.3.4 Static IPv6 Multicast Table	152
Chapter 10 Routing	154
10.1 Interface	154
10.2 Routing Table	160
10.2.1 IPv4 Routing Table	160
10.2.2 IPv6 Routing Table	160
10.3 Static Routing	161
10.3.1 IPv4 Static Routing Config	161
10.3.2 IPv6 Static Routing Config	162
10.4 DHCP Relay	163
10.4.1 Global Config	165
10.4.2 DHCP Server	166
10.5 ARP	167
10.5.1 ARP Table	167
10.5.2 Static ARP	167
Chapter 11 QoS	169
11.1 DiffServ	172
11.1.1 Port Priority	172
11.1.2 Schedule Mode	173
11.1.3 802.1P Priority	174
11.1.4 DSCP Priority	175
11.2 Bandwidth Control	177
11.2.1 Rate Limit	177
11.2.2 Storm Control	178
11.3 Voice VLAN	179
11.3.1 Global Config	181
11.3.2 Port Config	182
11.3.3 OUI Config	183
Chapter 12 ACL	185
12.1 Time-Range	185
12.1.1 Time-Range Summary	185
12.1.2 Time-Range Create	186
12.1.3 Holiday Config	187
12.2 ACL Config	187
12.2.1 ACL Summary	187
12.2.2 ACL Create	188
12.2.3 MAC ACL	188
12.2.4 Standard-IP ACL	190
12.2.5 Extend-IP ACL	191
12.2.6 IPv6 ACL	192
12.3 Policy Config	193
12.3.1 Policy Summary	193
12.3.2 Policy Create	194
12.3.3 Action Create	194
12.4 ACL Binding	195
12.4.1 Binding Table	196
12.4.2 Port Binding	197
12.4.3 VLAN Binding	198
12.5 Policy Binding	198
12.5.1 Binding Table	199
12.5.2 Port Binding	200
12.5.3 VLAN Binding	201
12.6 Application Example for ACL	201
Chapter 13 Network Security	204
13.1 IP-MAC Binding	204
13.1.1 Binding Table	204
13.1.2 Manual Binding	205
13.1.3 ARP Scanning	207
13.2 DHCP Snooping	209
13.2.1 Global Config	212
13.2.2 Port Config	212
13.2.3 Option 82 Config	214
13.3 ARP Inspection	215
13.3.1 ARP Detect	219
13.3.2 ARP Defend	220
13.3.3 ARP Statistics	221
13.4 DoS Defend	222
13.4.1 DoS Defend	224
13.5 802.1X	224
13.5.1 Global Config	228
13.5.2 Port Config	229
13.6 AAA	231
13.6.1 Global Config	232
13.6.2 Privilege Elevation	232
13.6.3 RADIUS Server Config	233
13.6.4 TACACS+ Server Config	234
13.6.5 Authentication Server Group Config	234
13.6.6 Authentication Method List Config	236
13.6.7 Application Authentication List Config	237
13.6.8 802.1X Authentication Server Config	238
13.6.9 Default Settings	238
Chapter 14 SNMP	240
14.1 SNMP Config	242
14.1.1 Global Config	242
14.1.2 SNMP View	243
14.1.3 SNMP Group	244
14.1.4 SNMP User	245
14.1.5 SNMP Community	247
14.2 Notification	249
14.3 RMON	251
14.3.1 Statistics	252
14.3.2 History	253
14.3.3 Event	254
14.3.4 Alarm Config	255
Chapter 15 LLDP	257
15.1 Basic Config	261
15.1.1 Global Config	261
15.1.2 Port Config	262
15.2 Device Info	263
15.2.1 Local Info	263
15.2.2 Neighbor Info	264
15.3 Device Statistics	265
15.4 LLDP-MED	267
15.4.1 Global Config	268
15.4.2 Port Config	268
15.4.3 Local Info	271
15.4.4 Neighbor Info	272
Chapter 16 Maintenance	273
16.1 System Monitor	273
16.1.1 CPU Monitor	273
16.1.2 Memory Monitor	274
16.2 Log	274
16.2.1 Log Table	275
16.2.2 Local Log	276
16.2.3 Remote Log	277
16.2.4 Backup Log	277
16.3 Device Diagnose	278
16.3.1 Cable Test	278
16.4 Network Diagnose	279
16.4.1 Ping	280
16.4.2 Tracert	280
Appendix A: Specifications	282

Match case Limit results 1 per page

Select:

Select the desired port for Loopback Detection configuration. It is

multi-optional.

Port:

Displays the port number.

Status:

Enable or disable Loopback Detection function for the port.

Operation Mode:

Select the mode how the switch processes the detected loops.



Alert:

When a loop is detected, display an alert.



Port based

: When a loop is detected, display an alert and

block the port.

Recovery Mode:

Select the mode how the blocked port recovers to normal status.



Auto

: Block status can be automatically removed after

recovery time.



Manual

: Block status only can be removed manually.

Loop Status:

Displays the port status whether a loopback is detected.

Block Status:

Displays the port status about block or unblock.

LAG:

Displays the LAG number the port belongs to.

Recover:

Click the

Recover

button to manually remove the block status of

selected ports.

Note:

Loopback Detection must coordinate with storm control.

6.2 LAG

LAG (Link Aggregation Group) is to combine a number of ports together to make a single

high-bandwidth data path, so as to implement the traffic load sharing among the member ports in

the group and to enhance the connection reliability.

For the member ports in an aggregation group, their basic configuration must be the same. The

basic configuration includes

STP

QoS

VLAN

port attributes

MAC Address Learning mode

and other associated settings. More details are explained below:



If the ports, which are enabled for the

802.1Q VLAN

STP

QoS

and

Port Configuration

(

Speed and Flow Control

), are in a LAG, their configurations would be the same as the

LAG’s.



The ports, which are enabled for the

half-duplex

Port Security

Port Mirror

and

MAC

Address Filtering

, cannot be added to the LAG.

If the LAG is needed, you are suggested to configure the LAG function here before configuring the

other functions for the member ports.

Tips:

Calculate the bandwidth for a LAG: If a LAG consists of the four ports in the speed of

1000Mbps Full Duplex, the whole bandwidth of the LAG is up to 8000Mbps (2000Mbps * 4)

because the bandwidth of each member port is 2000Mbps counting the up-linked speed of

1000Mbps and the down-linked speed of 1000Mbps.