Yamaha CLP-470 Owner's Manual - Page 74

screws 4 x 20 mm., were attached in Step 2-1.

Get Yamaha CLP-470 PDF manuals and user guides View all Yamaha CLP-470 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

1. Attach C to D and E. 1-1 Untie and straighten out the bundled pedal cord. Do not discard the vinyl tie. You will need it later in step 5. 1-2 Attach D and E to C by tightening four long screws (6 x 20 mm). 3. Mount A. Be sure to place your hands at least 15 cm from either end of the main unit when positioning it. A D 1-2 C E Align the screw holes 15 cm or further in 1-1 2. Attach B. Depending on the model of instrument you purchased, the surface color of one side of B may be different from the other side. In this case, position B so that the side of the surface color most similar to D and E faces the player. 2-1 Align the screw holes on the upper side of B with the bracket holes on D and E, then attach the upper corners of B to D and E by fingertightening two thin screws (4 x 12 mm). 2-2 Secure the bottom end of B using four tapping screws (4 x 20 mm). 2-3 Securely tighten the screws on the top of B that were attached in Step 2-1. E 2-1 2-3 B D 2-2 CAUTION Be extra careful not to drop or let your fingers be pinched by the main unit. CAUTION Do not hold the main unit in any position other than the position specified above 4. Secure A. 4-1 Adjust the position of A so that the left and right ends of A will project beyond D and E equally (as seen from the front). 4-2 Secure A by tightening six short screws (6 x 16 mm) from the front. 4-1 Projection of A A A 4-2 74 Appendix Assembling the Clavinova

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
74
Appendix
Assembling the Clavinova
1.
Attach C to D and E.
1-1
Untie and straighten out the bundled pedal cord.
Do not discard the vinyl tie. You will need it later
in step 5.
1-2
Attach D and E to C by tightening four long
screws (6 x 20 mm).
2.
Attach B.
Depending on the model of instrument you
purchased, the surface color of one side of B
may be different from the other side. In this
case, position B so that the side of the surface
color most similar to D and E faces the player.
2-1
Align the screw holes on the upper side of B
with the bracket holes on D and E, then attach
the upper corners of B to D and E by finger-
tightening two thin screws (4 x 12 mm).
2-2
Secure the bottom end of B using four tapping
screws (4 x 20 mm).
2-3
Securely tighten the screws on the top of B that
were attached in Step 2-1.
3.
Mount A.
Be sure to place your hands at least 15 cm from
either end of the main unit when positioning it.
CAUTION
Be extra careful not to drop or let your fingers be pinched by the
main unit.
CAUTION
Do not hold the main unit in any position other than the position
specified above
4.
Secure A.
4-1
Adjust the position of A so that the left and
right ends of A will project beyond D and E
equally (as seen from the front).
4-2
Secure A by tightening six short screws (6 x 16
mm) from the front.
C
D
E
1-2
1-1
2-1
2-3
B
E
D
2-2
A
15 cm or further in
Align the
screw holes
4-2
A
A
4-1
Projection of A