Yamaha CLP-470 Owner's Manual - Page 77

Attach D to E and F., Temporarily mount B., Mount A., long screws 6 x 20mm.

Get Yamaha CLP-470 PDF manuals and user guides View all Yamaha CLP-470 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

1. Attach D to E and F. 1-1 Attach D to E and F by using four long screws (6 x 20 mm). 1-2 Secure D from the rear using two long screws (6 x 20 mm). 1-3 Remove the twist tie from the folded pedal cord. Do not remove the twist tie that is located next to the hole. 1-1 F 1-3 E D 1-2 2. Temporarily mount B. 2-1 Insert B between E and F as shown in the illustration. 2-2 Align and attach B to the front side of D, E and F. 2-1 2-2 F B E D 2-3 Temporarily secure B by finger-tightening four long screws (6 x 20mm). * Insert four screws into the larger holes (all four holes) on the brackets. 2-4 Secure B using a thin screw (4 x 14 mm). * Insert the screw into the smaller hole on the bracket. 2-4 2-3 3. Mount A. 3-1 Place your hands at least 15 cm from either end of A to mount it. 3-2 Position A so that the stopper-wood on the rear side of the bottom of A will be located behind the front panel, then slide A slowly toward the rear while lightly pushing E and F toward the center. * Be sure to slide the guide pins  on each side of A into the guide slots  on E and F respectively. 15 cm or further in A F 3-2 3-1 15 cm or further in E CAUTION Be extra careful not to drop or let your fingers be pinched by the main unit. CAUTION Do not hold the main unit in any position other than the position specified above. Appendix 77 Assembling the Clavinova

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
77
Appendix
Assembling the Clavinova
1.
Attach D to E and F.
1-1
Attach D to E and F by using four long screws
(6 x 20 mm).
1-2
Secure D from the rear using two long screws
(6 x 20 mm).
1-3
Remove the twist tie from the folded pedal cord.
Do not remove the twist tie that is located next
to the hole.
2.
Temporarily mount B.
2-1
Insert B between E and F as shown in the
illustration.
2-2
Align and attach B to the front side of D, E and F.
2-3
Temporarily secure B by finger-tightening four
long screws (6 x 20mm).
*
Insert four screws into the larger holes (all four holes) on the
brackets.
2-4
Secure B using a thin screw (4 x 14 mm).
* Insert the screw into the smaller hole on the bracket.
3.
Mount A.
3-1
Place your hands at least 15 cm from either end
of A to mount it.
3-2
Position A so that the stopper-wood on the rear
side of the bottom of A will be located behind
the front panel, then slide A slowly toward the
rear while lightly pushing E and F toward the
center.
*
Be sure to slide the guide pins
1
on each side of A into the
guide slots
2
on E and F respectively.
CAUTION
Be extra careful not to drop or let your fingers be pinched by the
main unit.
CAUTION
Do not hold the main unit in any position other than the position
specified above.
1-2
1-1
1-3
E
D
F
2-2
2-1
F
E
B
D
2-3
2-4
3-1
A
F
E
3-2
15 cm or
further in
15 cm or
further in