Yamaha CLP-470 Owner's Manual - Page 78

Secure A., Connect the speaker cord., Attach C., shown, then clip the cord into the holders.

Get Yamaha CLP-470 PDF manuals and user guides View all Yamaha CLP-470 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

4. Secure A. 4-1 Secure A from the rear using two short screws (6 x 16 mm). 4-2 Secure A from the rear using two thin screws (4 x 14 mm). 4-3 Secure A from the front using four short screws (6 x 16mm). 4-2 A 6. Connect the pedal cord. 6-1 Insert the pedal cord plug into the [PEDAL] connector. 6-2 Attach the cord holders to the instrument as shown, then clip the cord into the holders. At this time, be careful not to allow too much slack in the pedal cord between the plug and cord holder. 6-1 4-1 4-3 4-4 Firmly tighten the screws you temporarily fastened on B in steps 2-3 above. 4-4 5. Connect the speaker cord. 5-1 Remove the twist tie attaching the speaker cord. 5-2 Insert the speaker cord plug into the connector so that the protruding tab on the plug faces toward right when viewed from the rear. 6-2 Insert the pedal cord E securely until the metal part of the cord plug disappears from view. Otherwise, the pedal may not function properly. 7. Attach C. 7-1 Place on D, the stopper-wood in the bottom corners of C, then attach the top of C. 7-2 Secure upper right and left of C using two thin screws (4 x 14 mm). 7-3 Secure upper center and bottom of C using five tapping screws (4 x 20 mm). 7-2 7-1 D C C 7-3 5-2 78 Appendix Assembling the Clavinova

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
78
Appendix
Assembling the Clavinova
4.
Secure A.
4-1
Secure A from the rear using two short screws
(6 x 16 mm).
4-2
Secure A from the rear using two thin screws
(4 x 14 mm).
4-3
Secure A from the front using four short screws
(6 x 16mm).
4-4
Firmly tighten the screws you temporarily
fastened on B in steps 2-3 above.
5.
Connect the speaker cord.
5-1
Remove the twist tie attaching the speaker cord.
5-2
Insert the speaker cord plug into the connector
so that the protruding tab on the plug faces
toward right when viewed from the rear.
6.
Connect the pedal cord.
6-1
Insert the pedal cord plug into the [PEDAL]
connector.
6-2
Attach the cord holders to the instrument as
shown, then clip the cord into the holders. At
this time, be careful not to allow too much slack
in the pedal cord between the plug and cord
holder.
7.
Attach C.
7-1
Place on D, the stopper-wood in the bottom
corners of C, then attach the top of C.
7-2
Secure upper right and left of C using two thin
screws (4 x 14 mm).
7-3
Secure upper center and bottom of C using five
tapping screws (4 x 20 mm).
4-1
4-2
4-3
A
4-4
5-2
6-1
6-2
E
Insert the pedal cord
securely until the metal
part of the cord plug
disappears from view.
Otherwise, the pedal may
not function properly.
7-2
7-3
C
7-1
D
C