Compaq Armada 6500 Compaq Storage Hub 12 Management Utilities Hardware and Sof - Page 13

Installation, Hardware Requirements, Organization of this Guide

Get Compaq Armada 6500 - Notebook PC PDF manuals and user guides View all Compaq Armada 6500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

1-2 Compaq Storage Hub 12 Management Utilities Hardware and Software User Guide Organization of this Guide continued For Information About Upgrading the management module firmware Configuring the management module Troubleshooting the management module See Appendix B Appendix C Appendix D Installation Before Compaq Storage Hub 12 Management Utilities can communicate with Compaq-managed devices, all devices must be properly configured, connected, and powered up. Refer to the Compaq Storage Hub 12 Management Module installation instructions to configure the module for management. Once the procedures have been completed, verify that the hardware and software requirements (listed below) are met, and then perform the HMU installation procedure. Hardware Requirements The following hardware is required to communicate with HMU: At least one Compaq Storage Hub 12 hub with a module A 32-bit PC capable of running Windows 95, Windows 98 or Windows NT 4.0 An Ethernet connection from the management PC to the managed device. This can be through an Ethernet hub or switch running 10 Base T IMPORTANT: While it may be possible to run HMU on a system that is also a server, we do not recommend that you do so; it is possible for the two applications to interfere with each other. Run HMU on its own dedicated workstation.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
1-2
Compaq Storage Hub 12 Management Utilities Hardware and Software User Guide
Organization of this Guide
continued
For Information About
See
Upgrading the management module firmware
Appendix B
Configuring the management module
Appendix C
Troubleshooting the management module
Appendix D
Installation
Before Compaq Storage Hub 12 Management Utilities can communicate with
Compaq-managed devices, all devices must be properly configured,
connected, and powered up. Refer to the Compaq Storage Hub 12
Management Module installation instructions to configure the module for
management. Once the procedures have been completed, verify that the
hardware and software requirements (listed below) are met, and then perform
the HMU installation procedure
.
Hardware Requirements
The following hardware is required to communicate with HMU:
■
At least one Compaq Storage Hub 12 hub with a module
■
A 32-bit PC capable of running Windows 95, Windows 98 or Windows
NT 4.0
■
An Ethernet connection from the management PC to the managed
device. This can be through an Ethernet hub or switch running 10
Base T
IMPORTANT:
While it may be possible to run HMU on a system that is also a server, we
do not recommend that you do so; it is possible for the two applications to interfere with
each other. Run HMU on its own dedicated workstation.