Compaq Armada 6500 Compaq Storage Hub 12 Management Utilities Hardware and Sof - Page 83

Downloading Hub Controller Firmware, the Boot Menu.

Get Compaq Armada 6500 - Notebook PC PDF manuals and user guides View all Compaq Armada 6500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

Upgrading the Firmware B-3 Downloading Hub Controller Firmware Follow the steps below to load new hub controller firmware on a local Compaq Storage Hub 12 hub or to a remote hub. This procedure must be run on all of your Compaq Storage Hub 12 hubs. Use an HMM that has had is device agent firmware already updated to the most recent revision. This procedure is covered in the previous section. If planning to download the hub controller firmware remotely through the device agent or master hub (i.e. the hub with the HMM in it) then update the firmware in that hub first. Alternatively, move the HMM to each hub temporarily and download the firmware through it locally. As noted, moving the HMM from hub to hub will be faster because the ethernet is several times faster than is communications through ICI. If the hub is already connected to the PC, skip to step 4. 1. Place the new firmware on a file system that is available to the PC management workstation that will be connected to the hub. The device agent firmware is distributed on the Compaq website: www.compaq.com. The most recent version of the firmware is located there. 2. If the PC is not connected to the HMM, connect the PC via a null modem cable to the RS-232 serial port on the HMM. There is an explanation of how to do this is in the Compaq Storage Hub 12 Management Module installation instructions. 3. Establish a terminal emulation session. This is explained in the information noted above. 4. Press the reset button located on the upper left side of the hub. The system will run the self-test. Press Enter on your keyboard to display the Boot Menu. If your download is local to this hub, select 2 Download and update Hub-Controller code in this hub from the Boot Menu. If your download is directed to this hub and/or to remote devices, from the Boot Menu, select 3 Download and update Hub-Controller code in a remote hub (via Agent). If you are using a HyperTerminal window, select Transfer, Send Text File. Open the file to be transferred. Otherwise, follow your terminal emulator's procedure for an ASCII download. The download should take less than 5 minutes. This procedure will reset the hub and display firmware version information. Once the agent has been upgraded, select 5 Start normal hub operation.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
Upgrading the Firmware
B-3
Downloading Hub Controller Firmware
Follow the steps below to load new hub controller firmware on a local
Compaq Storage Hub 12 hub or to a remote hub. This procedure must be run
on all of your Compaq Storage Hub 12 hubs. Use an HMM that has had is
device agent firmware already updated to the most recent revision. This
procedure is covered in the previous section.
If planning to download the hub controller firmware remotely through the
device agent or master hub (i.e. the hub with the HMM in it) then update the
firmware in that hub first. Alternatively, move the HMM to each hub
temporarily and download the firmware through it locally. As noted, moving
the HMM from hub to hub will be faster because the ethernet is several times
faster than is communications through ICI.
If the hub is already connected to the PC, skip to step 4.
1.
Place the new firmware on a file system that is available to the PC
management workstation that will be connected to the hub. The device
agent firmware is distributed on the Compaq website:
www.compaq.com
.
The most recent version of the firmware is located there.
2.
If the PC is not connected to the HMM, connect the PC via a null
modem cable to the RS-232 serial port on the HMM. There is an
explanation of how to do this is in the
Compaq Storage Hub 12
Management Module
installation instructions.
3.
Establish a terminal emulation session. This is explained in the
information noted above.
4.
Press the reset button located on the upper left side of the hub. The
system will run the self-test. Press
Enter
on your keyboard to display
the Boot Menu.
If your download is local to this hub,
select 2 Download and update
Hub-Controller code
in this hub from the Boot Menu. If your download is
directed to this hub and/or to remote devices, from the Boot Menu, select
3
Download and update Hub-Controller code in a remote hub (via Agent).
If you are using a HyperTerminal window, select
Transfer
, Send
Text File.
Open the file to be transferred. Otherwise, follow your terminal emulator’s
procedure for an ASCII download.
The download should take less than 5 minutes. This procedure will reset the
hub and display firmware version information.
Once the agent has been upgraded, select
5 Start normal hub operation.