Fluke 125 Fluke 125 Users Manual - Page 50

Performing Harmonics Measurements, Input Connections for Harmonics

Get Fluke 125 PDF manuals and user guides View all Fluke 125 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Fluke 125 Users Manual Performing Harmonics Measurements To perform harmonics measurements do the following: c Connect the inputs as indicated in figure 3-1 Connect input A for VOLT and for WATT, connect input B for AMP and for WATT. 10 mV/A - 1 mV/A BB120 Figure 3-1. Input Connections for Harmonics d Open the application mode menu. e Highlight HARMONICS f Accept your choice. You will see a screen like figure 3-2 If input A was already set to V, and input B was already set to AMP, the actual probe settings will be used. If not, a PROBE menu will be shown to enable you to select the appropriate probe setting. To change the probe settings if the PROBE menu is not automatically opened see Measurement Probes & Settings in chapter 1 . 3-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
Fluke 125
Users Manual
3-2
Performing Harmonics Measurements
To perform harmonics measurements do the following:
Connect the inputs as indicated in figure 3-1
Connect input A for VOLT and for WATT,
connect input B for AMP and for WATT.
BB120
10 mV/A -
1 mV/A
Figure 3-1. Input Connections for Harmonics
Open the application mode menu.
Highlight HARMONICS
Accept your choice. You will see a
screen like figure 3-2
If input A was already set to V, and input B was already set
to AMP, the actual probe settings will be used.
If not, a
PROBE menu will be shown to enable you to select the
appropriate probe setting.
To change the probe settings if the PROBE menu is not
automatically opened see Measurement Probes & Settings
in chapter 1 .