HP Rp2430 rp24xx A180 User Manual - Page 18

Acoustics (Germany), UK General Approval (United Kingdom only), Internal Modem and HP A2991-600xx

Get HP Rp2430 - Server - 650 MHz PDF manuals and user guides View all HP Rp2430 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

A-Class System Overview and Reference A-Class Server System Regulatory Compliance Statements Acoustics (Germany) Acoustic noise level per ISO 9296 (25° C): LpAm

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
A-Class System Overview and Reference
A-Class Server System Regulatory Compliance Statements
Chapter 1
18
Acoustics (Germany)
Acoustic noise level per ISO 9296 (25
°
C):
LpA
m
<57dB (operators position)
GerÌuschemission nach ISO 9296 (25
°
C):
LpA
m
<57dB (Arbeitsplatte)
UK General Approval (United Kingdom only)
Pursuant to Section 22 of Telecommunications Act of 1984, this product is approved for
indirect connection to Public Telecommunications systems within the United Kingdom
under the General Approval number NS/G/1234/J/100003.
Internal Modem and HP A2991-600xx Line Access Module (LAM)
The following warnings apply to the use of the HP 2991-60001 internal modem and HP
A2991-600xx LAM that may be provided with the computer.
Terminal DOC (Canada only)
NOTE
The Canadian Department of Communications label identifies certified equipment. This
certification means that the equipment meets certain telecommunication network
protective operational and safety requirements. The Department does not guarantee the
equipment will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The equipment must
also be installed using an acceptable method of connection. In some cases, the company's
inside wiring associated with a single line individual service may be extended by means
of a certified assembly (telephone extension cord). The customer should be aware that
compliance with the above conditions may not prevent degradation of service in some
situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly important in rural areas.
The Load Number (LN) assigned to each terminal device denotes the percentage of total
load to be connected to a telephone loop which is used by the device to prevent
overloading. The termination on a loop may consist of any combination of devices subject
only to the requirement that the total of the Load Numbers of all devices does not exceed
100. The load number for this product is 33.