HP Rp2430 rp24xx A180 User Manual - Page 27

Stand-Alone A-Class Server Unpack and Install Instructions, Overview, Open and Unload the Carton

Page 27 highlights

A-Class Server Installation Stand-Alone A-Class Server Unpack and Install Instructions NOTE Stand-Alone A-Class Server Unpack and Install Instructions Overview Unpacking the A-Class server consists of opening and unloading the carton. Inside the carton you will find, in addition to the server, an accessory kit and a packet containing installation instructions and regulatory information. • Open and Unload the Carton • Unpack the Server • Open the Accessory Kit • Open the Installation Instructions and Regulatory Information Packet The following instructions do not apply to A-Class servers that are received pre-installed in a cabinet. These procedures pertain to individual servers, only. Open and Unload the Carton Step 1. Place the sealed carton on a work surface with the correct side up as indicated by the "This Side Up" symbol (below). CAUTION Use sharp instruments carefully when unpacking electronics equipment. Failure to follow this precaution may result in personal injury or damage to components. Step 2. Carefully open the carton, remove the contents, and set them on the work surface. Each carton will contain: • The server. • An accessory kit. • A packet containing installation instructions and regulatory information. NOTE Report any missing items to your local Hewlett-Packard office immediately. If there is obvious freight damage, contact your shipper immediately. We recommend that you retain all packing materials in case any of the items received require return to Hewlett-Packard. Chapter 2 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106

A-Class Server Installation
Stand-Alone A-Class Server Unpack and Install Instructions
Chapter 2
27
Stand-Alone A-Class Server Unpack and Install
Instructions
Overview
Unpacking the A-Class server consists of opening and unloading the carton. Inside the
carton you will find, in addition to the server, an accessory kit and a packet containing
installation instructions and regulatory information.
Open and Unload the Carton
Unpack the Server
Open the Accessory Kit
Open the Installation Instructions and Regulatory Information Packet
NOTE
The following instructions do not apply to A-Class servers that are received pre-installed
in a cabinet. These procedures pertain to individual servers, only.
Open and Unload the Carton
Step 1.
Place the sealed carton on a work surface with the correct side up as indicated by the
“This Side Up” symbol (below).
CAUTION
Use sharp instruments carefully when unpacking electronics equipment. Failure to
follow this precaution may result in personal injury or damage to components.
Step 2.
Carefully open the carton, remove the contents, and set them on the work surface. Each
carton will contain:
The server.
An accessory kit.
A packet containing installation instructions and regulatory information.
NOTE
Report any missing items to your local Hewlett-Packard office immediately. If there is
obvious freight damage, contact your shipper immediately.
We recommend that you retain all packing materials in case any of the items received
require return to Hewlett-Packard.