HP Rp2430 rp24xx A180 User Manual - Page 92

A-Class Server Disk Drive Removal and Replacement, Overview, Electrostatic Discharge Precautions,

Get HP Rp2430 - Server - 650 MHz PDF manuals and user guides View all HP Rp2430 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

A-Class System Service A-Class Server Disk Drive Removal and Replacement CAUTION A-Class Server Disk Drive Removal and Replacement Overview This section provides step-by-step instructions for removing and replacing the Disk Drive Bracket and Disk Drives in the A-Class Server. The following subsections apply: • Remove the Bracket Containing the Disk Drive(s) • Remove the Disk Drive(s) • Disk Drive Replacement The procedures in this section require opening the system cabinet and exposing the system to electrostatic discharge. Always observe all electrostatic precautions when working with components inside or out of the cabinet. Failure to follow these precautions may result in component damage or loss of system reliability. Electrostatic Discharge Precautions • Use a grounding mat and an anti-static wrist strap. • Wear the anti-static wrist strap to ensure that any accumulated electrostatic charge is discharged from your body to ground. Before You Do Anything... Step 1. Perform system backup. Step 2. Shut down the operating system. Step 3. Power down the system. Step 4. Unplug the server. NOTE Cabinet-mounted servers must be removed from the cabinet before proceeding. Step 5. Remove the top of the server by unscrewing the knurled captive screws on each side of the rear of the server. Slide the top back, lift it off, and set it aside. 92 Chapter 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
A-Class System Service
A-Class Server Disk Drive Removal and Replacement
Chapter 3
92
A-Class Server Disk Drive Removal and Replacement
Overview
This section provides step-by-step instructions for removing and replacing the Disk
Drive Bracket and Disk Drives in the A-Class Server. The following subsections apply:
•
Remove the Bracket Containing the Disk Drive(s)
•
Remove the Disk Drive(s)
•
Disk Drive Replacement
CAUTION
The procedures in this section require opening the system cabinet and exposing the
system to electrostatic discharge. Always observe all electrostatic precautions when
working with components inside or out of the cabinet. Failure to follow these precautions
may result in component damage or loss of system reliability.
Electrostatic Discharge Precautions
•
Use a grounding mat and an anti-static wrist strap.
•
Wear the anti-static wrist strap to ensure that any accumulated electrostatic charge
is discharged from your body to ground.
Before You Do Anything...
Step 1.
Perform system backup.
Step 2.
Shut down the operating system.
Step 3.
Power down the system.
Step 4.
Unplug the server.
NOTE
Cabinet-mounted servers must be removed from the cabinet before proceeding.
Step 5.
Remove the top of the server by unscrewing the knurled captive screws on each side of
the rear of the server. Slide the top back, lift it off, and set it aside.