Yamaha RX-V3900BL Owner's Manual - Page 115

Remote control features Programming codes from other remote controls You can program remote control codes from other remote controls. Use the learning feature if you want to program functions not included in the basic operations covered by the remote control codes, or an appropriate remote control code is not available. You can program the function of other remote control to the buttons in the highlighted areas in the following illustration. The buttons can be programmed independently for each control area. SUBMENU RETURN ENTER PRESET/CH STATUS TITLE BAND 2 1 SELECT DVD TV XM BD HD DVD CBL SAT TUNER AV TV 4 Place this remote control about 5 to 10 cm (2 to 4 in) apart from the other remote control on a flat surface so that their infrared transmitters are aimed at each other and then press 9ENTER. "L-KEY" appears in the display window (4). Other remote control POWER POWER STANDBY POWER MULTI V-AUX PHONO DOCK CD DVR SIRIUS SETUP ID MACRO MODE ZONE SYSTEM MEMORY 3 VOLUME MENU SRCH MODE CAT. A-E PLAY INFO DISPLAY MD CD-R VCR USB NET AMP TV SOURCE 4 POWER POWER STANDBY POWER TV AV MULTI V-AUX PHONO DOCK BD HD DVD CBL SAT TUNER DVD TV XM CD MD CD-R DVR VCR SIRIUS USB NET AMP TV SOURCE SELECT SETUP ID MACRO MODE ZONE SYSTEM MEMORY 1 2 3 4 STATUS TITLE BAND PRESET/CH VOLUME MENU SRCH MODE ENTER CAT. A-E SUBMENU RETURN MEMORY PLAY INFO DISPLAY MUTE REC Set to SOURCE STATUS TITLE BAND PRESET/CH VOLUME MENU SRCH MODE ENTER CAT. A-E SUBMENU RETURN MEMORY PLAY INFO DISPLAY MUTE REC TAG PRG SELECT CLASSICAL LIVE/CLUB ENTERTAIN MOVIE 1 2 3 4 STEREO ENHANCER SUR.DECODE STRAIGHT 5 6 7 8 HDMI OUT EXTD SUR. PURE DIRECT 9 0 10 ENT INFO TV VOL LEVEL TV CH SLEEP MUTE TV INPUT AUDIO SEL AUDIO 3D DSP STATUS TITLE BAND 1 5 to 10 cm (2 to 4 in) 5 Press the button for which you want to program the new function. "START" appears in the display window (4). TV POWER POWER STANDBY POWER AV MULTI V-AUX PHONO DOCK BD HD DVD CBL SAT TUNER SUBMENU RETURN SELECT DVD TV XM SIRIUS SETUP ID MACRO MODE ZONE SYSTEM MEMORY 2 PRESET/CH ENTER PLAY INFO DISPLAY Notes • The remote control transmits infrared rays. If the other remote control also uses infrared rays, this remote control can learn most of its functions. However, you may not be able to program some special signals or extremely long transmissions. • You cannot program the desired remote control code even if you select the buttons in the highlighted area in the above illustration depending on the selected control area and the assigned library. 1 Set the operation mode selector to FSOURCE and then press an input selector button (3) to select the desired control area. If you want to program the remote control code for "TV", set the operation mode selector to FTV. Note Make sure that the operation mode selector is set to FSOURCE or FTV. When you set the operation mode selector to FAMP and program a remote control codes from other remote controls, the programmed key cannot operate the amplifier function of this unit. 2 Press GSETUP using a ballpoint pen or similar object. "SETUP" appears in the display window (4). VOLUME MENU SRCH MODE PRESET/CH STATUS TITLE BAND CAT. A-E 4 3 2 1 SYSTEM MEMORY SETUP ID MACRO MODE ZONE VOLUME MENU SRCH MODE SELECT AMP TV SOURCE 4 3 USB NET SIRIUS VCR DVR DVD TV XM BD HD DVD CBL SAT TUNER AMP TV SOURCE MD CD-R CD USB NET MULTI V-AUX PHONO DOCK VCR DVR AV TV MD CD-R CD POWER POWER STANDBY POWER 6 Press and hold the button you want to program on the other remote control until "OK" appears in the display window (4). "NG" appears in the display window (4) if learning was unsuccessful. In this case, start over from step 4. Other remote control OK y When you want to program another function, repeat steps 4 througn 6. 3 Press 9k / n repeatedly to select "LEARN" and then press 9ENTER. ADVANCED OPERATION English 111 En