Yamaha RX-V3900BL Owner's Manual - Page 131

Out Dvr, Vcr Or Md, Check Sp Wires

Get Yamaha RX-V3900BL - Network Home Theater Receiver PDF manuals and user guides
UPC - 705105565903
View all Yamaha RX-V3900BL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

Troubleshooting Problem Cause Remedy An audio source cannot be recorded by the digital recording component connected to the DIGITAL OUTPUT jacks. The audio source component is not connected to the DIGITAL INPUT jacks. Some components cannot records Dolby Digital or DTS sources. You are trying to record an audio source input at the DOCK terminal by the digital recording component connected to the DIGITAL OUTPUT jacks. Connect the audio source component to the DIGITAL INPUT jacks. Connect the recording component to the analog AUDIO OUT (DVR, VCR or MD/CD-R) jacks. (U.S.A. model only) HD Radio signals are not output at the DIGITAL OUTPUT jacks Connect the recording component to the analog AUDIO OUT (DVR, VCR or MD/CD-R) jacks. An audio source cannot be recorded by the analog recording component connected to the analog AUDIO OUT (DVR, VCR or MD/ CD-R) jacks. The audio source component is not connected to the analog AUDIO IN jacks. XM Satellite Radio and SIRIUS Satellite Radio signals are not output at the analog AUDIO OUT (DVR, VCR or MD/CD-R) jacks. Connect the audio source component to the AUDIO IN jacks. Recorded materials sound differently. The settings made on this unit (such as tonal quality, volume level and sound field programs) do not affect recorded material. The sound field parameters and some other settings of this unit cannot be changed. "Memory Guard" is set to "On". Set "Memory Guard" to "Off". This unit does not operate properly. The internal microcomputer has been frozen by an external electric shock (such as lightning or excessive static electricity) or by a power supply with low voltage. Disconnect the power cable from the AC wall outlet and then plug it in again after about 30 seconds. "CHECK SP WIRES" appears in the front panel display. Speaker cables are short-circuited. Make sure all speaker cables are connected correctly. There is noise interference from digital or radio frequency equipment. This unit is too close to the digital or highfrequency equipment. Move this unit further away from such equipment. The picture is disturbed. The video source uses scrambled or encoded signals to prevent dubbing. This unit suddenly enters the standby mode. The internal temperature becomes too high and the overheat protection circuitry has been activated. Wait about 1 hour for this unit to cool down and then turn it back on. See page 20 20 20 20 97 - 12 - - ADDITIONAL INFORMATION English 127 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
127
En
Troubleshooting
ADDITIONAL
INFORMATION
English
An audio source
cannot be recorded by
the digital recording
component connected
to the DIGITAL
OUTPUT jacks.
The audio source component is not
connected to the DIGITAL INPUT jacks.
Connect the audio source component to the DIGITAL
INPUT jacks.
20
Some components cannot records Dolby
Digital or DTS sources.
You are trying to record an audio source
input at the DOCK terminal by the digital
recording component connected to the
DIGITAL OUTPUT jacks.
Connect the recording component to the analog
AUDIO OUT (DVR, VCR or MD/CD-R) jacks.
20
(U.S.A. model only)
HD Radio signals are not output at the
DIGITAL OUTPUT jacks
Connect the recording component to the analog
AUDIO OUT (DVR, VCR or MD/CD-R) jacks.
20
An audio source
cannot be recorded by
the analog recording
component connected
to the analog AUDIO
OUT (DVR, VCR or MD/
CD-R) jacks.
The audio source component is not
connected to the analog AUDIO IN jacks.
Connect the audio source component to the AUDIO
IN jacks.
20
XM Satellite Radio and SIRIUS Satellite
Radio signals are not output at the analog
AUDIO OUT (DVR, VCR or MD/CD-R)
jacks.
Recorded materials
sound differently.
The settings made on this unit (such as
tonal quality, volume level and sound field
programs) do not affect recorded material.
The sound field
parameters and some
other settings of this
unit cannot be
changed.
“Memory Guard” is set to “On”.
Set “Memory Guard” to “Off”.
97
This unit does not
operate properly.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
Disconnect the power cable from the AC wall outlet
and then plug it in again after about 30 seconds.
—
“CHECK SP WIRES”
appears in the front
panel display.
Speaker cables are short-circuited.
Make sure all speaker cables are connected correctly.
12
There is noise
interference from
digital or radio
frequency equipment.
This unit is too close to the digital or high-
frequency equipment.
Move this unit further away from such equipment.
—
The picture is
disturbed.
The video source uses scrambled or
encoded signals to prevent dubbing.
This unit suddenly
enters the standby
mode.
The internal temperature becomes too
high and the overheat protection circuitry
has been activated.
Wait about 1 hour for this unit to cool down and then
turn it back on.
—
Problem
Cause
Remedy
See
page