Yamaha RX-V3900BL Owner's Manual - Page 35

Basic automatic setup

Get Yamaha RX-V3900BL - Network Home Theater Receiver PDF manuals and user guides
UPC - 705105565903
View all Yamaha RX-V3900BL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

PREPARATION Optimizer microphone Optimizing the speaker setting for your listening room 4 Disconnect the optimizer microphone to complete the automatic setup. y You can check the results of the measurements by using the GUI screen (page 34). y It is recommended that you use a tripod (etc.) to affix the optimizer microphone at the same height as your ears would be when you are seated in your listening position. You can use the attached screw of a tripod (etc.) to fix the optimizer microphone to the tripod (etc.). Before proceeding next operation Once you perform the next operation, this unit starts the automatic setup procedure in 10 seconds. During the automatic setup procedure, do not perform any operation on this unit. For more accurate measurements, we recommended that you get out of the room or move to the wall where speakers are not around during the measurement. It takes approximately 3 minutes. 3 Press 9ENTER to start the measurement. This unit starts to count down from 10 seconds. y • To start the measurement immediately, press 9ENTER again. • To cancel the automatic setup and return to the previous screen, press 0RETURN. Loud test tones are output from each speaker during the measurement. Once all items are measured, "COMPLETED" appears. COMPLETED PLS UNPLUG MIC Note If an error or warning message appears, see "Automatic setup" (page 136). ERROR: E-01 PRESS ENTER Basic automatic setup Use this feature to optimize the setup of this unit this unit for one listening position. You can also select the parameters to be optimized in the automatic setup. 1 Turn on the video monitor and then follow steps 1 and 2 in "Quick automatic setup" (page 30). 2 Press IMENU on the remote control. The following screen (GUI menu) appears in the video monitor. Information Setup Menu Start NOTICE Loud test tones are output. Please keep quiet or leave the room. Start:ENTER 3 To select the parameters to be optimized, press 9k to select "Setup Menu" and then press 9h. When you do not need to select the parameters to be optimized, skip to step 6. y If you do not select the parameters to be optimized, this unit will optimize the parameters you selected last time. All the parameters are selected by the initial factory settings. 4 Press 9k / n repeatedly to select the parameter and then press 9ENTER to check or uncheck the box. Check the boxes for the parameters to be optimized. Parameter Descriptions Multi Measure (Multiple point measurement) You can optimize the setup of this unit for multiple listening positions. For details, see "Advanced automatic setup" (page 33). In the basic automatic setup, leave this setting to the default. Wiring (Speaker wiring) This unit checks and adjusts which speakers are connected and the polarity of each speaker. English 31 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
31
En
Optimizing the speaker setting for your listening room
PREPARATION
English
y
It is recommended that you use a tripod (etc.) to affix the
optimizer microphone at the same height as your ears
would be when you are seated in your listening position.
You can use the attached screw of a tripod (etc.) to fix the
optimizer microphone to the tripod (etc.).
3
Press
9
ENTER
to start the measurement.
This unit starts to count down from 10 seconds.
y
•
To start the measurement immediately, press
9
ENTER
again.
•
To cancel the automatic setup and return to the previous
screen, press
0
RETURN
.
Loud test tones are output from each speaker during
the measurement. Once all items are measured,
“COMPLETED” appears.
If an error or warning message appears, see “Automatic
setup” (page 136).
4
Disconnect the optimizer microphone to
complete the automatic setup.
y
You can check the results of the measurements by using
the GUI screen (page 34).
Use this feature to optimize the setup of this unit this unit
for one listening position. You can also select the
parameters to be optimized in the automatic setup.
1
Turn on the video monitor and then follow
steps 1 and 2 in “Quick automatic setup”
(page 30).
2
Press
I
MENU
on the remote control.
The following screen (GUI menu) appears in the
video monitor.
3
To select the parameters to be optimized,
press
9
k
to select “Setup Menu” and then
press
9
h
.
When you do not need to select the parameters to be
optimized, skip to step 6.
y
If you do not select the parameters to be optimized, this
unit will optimize the parameters you selected last time.
All the parameters are selected by the initial factory
settings.
4
Press
9
k
/
n
repeatedly to select the
parameter and then press
9
ENTER
to
check or uncheck the box.
Check the boxes for the parameters to be optimized.
Before proceeding next operation
Once you perform the next operation, this unit starts the
automatic setup procedure in 10 seconds. During the
automatic setup procedure, do not perform any operation on
this unit. For more accurate measurements, we recommended
that you get out of the room or move to the wall where
speakers are not around during the measurement. It takes
approximately 3 minutes.
Note
Optimizer microphone
COMPLETED
PLS UNPLUG MIC
ERROR: E-01
PRESS ENTER
Basic automatic setup
Parameter
Descriptions
Multi Measure
(Multiple point
measurement)
You can optimize the setup of this unit for
multiple listening positions. For details, see
“Advanced automatic setup” (page 33). In
the basic automatic setup, leave this setting
to the default.
Wiring
(Speaker wiring)
This unit checks and adjusts which speakers
are connected and the polarity of each
speaker.
Information
Setup Menu
Start
NOTICE
Loud test tones are
output.
Please keep quiet
or leave the room.
Start:ENTER