Dell PowerEdge MX740c EMC PowerEdge MX740c Installation and Service Manual - Page 100

Installing the M.2 BOSS card, Removing the M.2 BOSS card

Get Dell PowerEdge MX740c PDF manuals and user guides View all Dell PowerEdge MX740c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

Figure 72. Removing the M.2 BOSS card Next steps 1. Install the M.2 BOSS card. Installing the M.2 BOSS card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your sled on page 42. Steps 1. Align the M.2 BOSS card at angle of 45 degrees with the SATA connector on the M.2 BOSS module. 2. Press the M.2 BOSS card into the SATA connector until firmly seated in place. 3. Push down the M.2 BOSS card and using Phillips #1 screwdriver, secure the M.2 BOSS card to the module. 100 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Figure 72. Removing the M.2 BOSS card
Next steps
1.
Install the M.2 BOSS card
.
Installing the M.2 BOSS card
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your sled
on page 42.
Steps
1.
Align the M.2 BOSS card at angle of 45 degrees with the SATA connector on the M.2 BOSS module.
2.
Press the M.2 BOSS card into the SATA connector until firmly seated in place.
3.
Push down the M.2 BOSS card and using Phillips #1 screwdriver, secure the M.2 BOSS card to the module.
100
Installing and removing system components