Dell PowerEdge MX740c EMC PowerEdge MX740c Installation and Service Manual - Page 57

Installing drive backplane

Get Dell PowerEdge MX740c PDF manuals and user guides View all Dell PowerEdge MX740c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Figure 30. Installing drive backplane Next steps 1. Connect the cables to the backplane connectors. NOTE: Verify backplane connector pins are not bent and then connect the signal cable to the backplane. NOTE: Verify both power and signal cable connections are fully seated to backplane and system board. NOTE: Connect the integrated cable to the backplane and system board if there is no PERC card installed in the system. 2. Install the drives. 3. Follow the procedure listed in After working inside the sled. Installing and removing system components 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Figure 30. Installing drive backplane
Next steps
1.
Connect the cables to the backplane connectors.
NOTE:
Verify backplane connector pins are not bent and then connect the signal cable to the backplane.
NOTE:
Verify both power and signal cable connections are fully seated to backplane and system board.
NOTE:
Connect the integrated cable to the backplane and system board if there is no PERC card installed in the
system.
2.
Install the drives
.
3.
Follow the procedure listed in
After working inside the sled
.
Installing and removing system components
57