Dell PowerEdge MX740c EMC PowerEdge MX740c Installation and Service Manual - Page 104

Installing the mini Mezzanine card

Get Dell PowerEdge MX740c PDF manuals and user guides View all Dell PowerEdge MX740c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

Figure 76. Removing the mini Mezzanine card NOTE: Install the connector cap on the I/O connector of the mini Mezzanine card, when not installed on system board. Next steps 1. Follow the procedure listed in After working inside your sled on page 42. Installing the mini Mezzanine card Prerequisites 1. Follow the safety guidelines listed in Safety Instructions. 2. Follow the procedure listed in Before working inside the sled. NOTE: The mini Mezzanine card is supported only on systems with two processors. Steps 1. Remove the connector cap on the I/O connector of the mini Mezzanine card. 2. Pull the blue pull tag to raise the lever on the mini Mezzanine card. 3. Align the mini Mezzanine card connector with the connector on the system board. 4. Lower the mini Mezzanine card into place, and push the lever down to lock the card in place. 104 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Figure 76. Removing the mini Mezzanine card
NOTE:
Install the connector cap on the I/O connector of the mini Mezzanine card, when not installed on system board.
Next steps
1.
Follow the procedure listed in
After working inside your sled
on page 42.
Installing the mini Mezzanine card
Prerequisites
1.
Follow the safety guidelines listed in
Safety Instructions
.
2.
Follow the procedure listed in
Before working inside the sled
.
NOTE:
The mini Mezzanine card is supported only on systems with two processors.
Steps
1.
Remove the connector cap on the I/O connector of the mini Mezzanine card.
2.
Pull the blue pull tag to raise the lever on the mini Mezzanine card.
3.
Align the mini Mezzanine card connector with the connector on the system board.
4.
Lower the mini Mezzanine card into place, and push the lever down to lock the card in place.
104
Installing and removing system components