Dell PowerEdge MX740c EMC PowerEdge MX740c Installation and Service Manual - Page 89

PERC card

Get Dell PowerEdge MX740c PDF manuals and user guides View all Dell PowerEdge MX740c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

CAUTION: If either the system board or iDRAC card fails, it is required to replace both system board and iDRAC card at the same time. Steps 1. Align the iDRAC card with the guide pin on the system board. 2. Lower the iDRAC card into place until the iDRAC connector is fully seated. 3. Press the blue touch points till the iDRAC card is firmly seated on the system board connector. Figure 60. Installing the iDRAC card Figure 61. Installing a vFlash card Next steps 1. Follow the procedure listed in After working inside your sled on page 42. PERC card Your system includes dedicated slots on the system board for PERC cards. Installing and removing system components 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
CAUTION:
If either the system board or iDRAC card fails, it is required to replace both system board and iDRAC
card at the same time.
Steps
1.
Align the iDRAC card with the guide pin on the system board.
2.
Lower the iDRAC card into place until the iDRAC connector is fully seated.
3.
Press the blue touch points till the iDRAC card is firmly seated on the system board connector.
Figure 60. Installing the iDRAC card
Figure 61. Installing a vFlash card
Next steps
1.
Follow the procedure listed in
After working inside your sled
on page 42.
PERC card
Your system includes dedicated slots on the system board for PERC cards.
Installing and removing system components
89