Dell PowerEdge MX740c EMC PowerEdge MX740c Installation and Service Manual - Page 91

Removing the Jumbo PERC card, Installing the PERC card

Get Dell PowerEdge MX740c PDF manuals and user guides View all Dell PowerEdge MX740c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

4. Press the PERC card to firmly seat in the system board connector. Figure 63. Installing the PERC card 5. Close the lever on the PERC card. Next steps 1. Connect the cable to the PERC card. 2. Follow the procedure listed in After working inside your sled on page 42. Removing the Jumbo PERC card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your sled. 3. Disconnect the cable connected to the Jumbo PERC card. Steps 1. Pull the two blue pull tags to raise the lever up on the Jumbo PERC card. 2. Holding both the blue pull tags, lift the Jumbo PERC card away from the system. 3. Install the connector cap on the I/O connector of the Jumbo PERC card. Installing and removing system components 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
4.
Press the PERC card to firmly seat in the system board connector.
Figure 63. Installing the PERC card
5.
Close the lever on the PERC card.
Next steps
1.
Connect the cable to the PERC card.
2.
Follow the procedure listed in
After working inside your sled
on page 42.
Removing the Jumbo PERC card
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your sled
.
3.
Disconnect the cable connected to the Jumbo PERC card.
Steps
1.
Pull the two blue pull tags to raise the lever up on the Jumbo PERC card.
2.
Holding both the blue pull tags, lift the Jumbo PERC card away from the system.
3.
Install the connector cap on the I/O connector of the Jumbo PERC card.
Installing and removing system components
91