Dell PowerEdge MX740c EMC PowerEdge MX740c Installation and Service Manual - Page 93

Optional Internal dual SD module, Removing the IDSDM card

Get Dell PowerEdge MX740c PDF manuals and user guides View all Dell PowerEdge MX740c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

Figure 65. Installing the Jumbo PERC card Next steps 1. Connect the cable on the Jumbo PERC card. 2. Follow the procedure listed in the After working inside your sled. Optional Internal dual SD module The IDSDM module combines the IDSDM features into a single module. NOTE: The write-protect switch is on the IDSDM module. Removing the IDSDM card Prerequisites 1. Follow the safety guidelines listed in Safety Instructions. 2. Follow the procedure listed in Before working inside the sled. 3. Remove the air shroud. Steps 1. Locate the IDSDM card connector on the system board. To locate IDSDM connector, see the system board jumpers and connectors section. 2. Using the Phillips #2 screwdriver, loosen the retention screw that connects the internal dual SD card (IDSDM) to the system board. CAUTION: To prevent damage to the IDSDM card, you must not tilt the card while lifting it from the system board. 3. Lift the release tab that secures the IDSDM to the system board. 4. Holding both ends of the IDSDM, lift the IDSDM out of the BOSS connector on the system board. Installing and removing system components 93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Figure 65. Installing the Jumbo PERC card
Next steps
1.
Connect the cable on the Jumbo PERC card.
2.
Follow the procedure listed in the
After working inside your sled
.
Optional Internal dual SD module
The IDSDM module combines the IDSDM features into a single module.
NOTE:
The write-protect switch is on the IDSDM module.
Removing the IDSDM card
Prerequisites
1.
Follow the safety guidelines listed in
Safety Instructions
.
2.
Follow the procedure listed in
Before working inside the sled
.
3.
Remove the air shroud
.
Steps
1.
Locate the IDSDM card connector on the system board. To locate IDSDM connector, see the
system board jumpers and
connectors
section.
2.
Using the Phillips #2 screwdriver, loosen the retention screw that connects the internal dual SD card (IDSDM) to the system
board.
CAUTION:
To prevent damage to the IDSDM card, you must not tilt the card while lifting it from the system
board.
3.
Lift the release tab that secures the IDSDM to the system board.
4.
Holding both ends of the IDSDM, lift the IDSDM out of the BOSS connector on the system board.
Installing and removing system components
93