Dell PowerEdge MX740c EMC PowerEdge MX740c Installation and Service Manual - Page 96

Installing a MicroSD card, Next steps, Prerequisites, Internal SD Card Port, Steps

Get Dell PowerEdge MX740c PDF manuals and user guides View all Dell PowerEdge MX740c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

Figure 68. Removing a MicroSD card Next steps 1. Install a MicroSD card. 2. Follow the procedure listed in After working inside your sled Installing a MicroSD card Prerequisites 1. Follow the safety guidelines listed in Safety Instructions. 2. Follow the procedure listed in Before working inside the sled. NOTE: To use an MicroSD card with your system, ensure that the Internal SD Card Port is enabled in System Setup. NOTE: If reinstalling, ensure that you install the MicroSD cards into the same slots based on the labels you had marked on the cards during removal. Steps 1. Locate the MicroSD card slot on the IDSDM card. Orient the MicroSD card appropriately and place the contact-pin end of the card into the slot. NOTE: The slot is keyed to ensure correct installation of the card. 2. Press the card into the card slot to lock it into their original location. 96 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Figure 68. Removing a MicroSD card
Next steps
1.
Install a MicroSD card
.
2.
Follow the procedure listed in
After working inside your sled
Installing a MicroSD card
Prerequisites
1.
Follow the safety guidelines listed in
Safety Instructions
.
2.
Follow the procedure listed in
Before working inside the sled
.
NOTE:
To use an MicroSD card with your system, ensure that the
Internal SD Card Port
is enabled in System Setup.
NOTE:
If reinstalling, ensure that you install the MicroSD cards into the same slots based on the labels you had marked
on the cards during removal.
Steps
1.
Locate the MicroSD card slot on the IDSDM card. Orient the MicroSD card appropriately and place the contact-pin end of
the card into the slot.
NOTE:
The slot is keyed to ensure correct installation of the card.
2.
Press the card into the card slot to lock it into their original location.
96
Installing and removing system components