Dell PowerEdge MX740c EMC PowerEdge MX740c Installation and Service Manual - Page 101

Mezzanine card, Removing the Mezzanine card

Get Dell PowerEdge MX740c PDF manuals and user guides View all Dell PowerEdge MX740c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

Figure 73. Installing the M.2 BOSS card Next steps 1. Install the M.2 BOSS module. 2. Follow the procedure listed in the After working inside your sled. Mezzanine card Your system supports two mezzanine cards: ● PCIe mezzanine card slot A supports fabric A. This card must match the fabric type of I/O modules installed in I/O module bays A1. ● PCIe mezzanine card slot B supports fabric B. This card must match the fabric type of I/O modules installed in I/O module bays B1. NOTE: The Mezzanine B1 card requires processor 2 to be installed. Removing the Mezzanine card Prerequisites 1. Follow the safety guidelines listed in Safety Instructions. 2. Follow the procedure listed in Before working inside the sled. Steps 1. Use the Phillips #2 screwdriver, loosen the captive screws that secure the Mezzanine card to the system. 2. Lift the Mezzanine card out of the sled. NOTE: To prevent damage to Mezzanine card, you must hold the card only by its edges. Installing and removing system components 101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Figure 73. Installing the M.2 BOSS card
Next steps
1.
Install the M.2 BOSS module
.
2.
Follow the procedure listed in the
After working inside your sled
.
Mezzanine card
Your system supports two mezzanine cards:
●
PCIe mezzanine card slot A supports fabric A. This card must match the fabric type of I/O modules installed in I/O module
bays A1.
●
PCIe mezzanine card slot B supports fabric B. This card must match the fabric type of I/O modules installed in I/O module
bays B1.
NOTE:
The Mezzanine B1 card requires processor 2 to be installed.
Removing the Mezzanine card
Prerequisites
1.
Follow the safety guidelines listed in
Safety Instructions
.
2.
Follow the procedure listed in
Before working inside the sled
.
Steps
1.
Use the Phillips #2 screwdriver, loosen the captive screws that secure the Mezzanine card to the system.
2.
Lift the Mezzanine card out of the sled.
NOTE:
To prevent damage to Mezzanine card, you must hold the card only by its edges.
Installing and removing system components
101