Dell PowerEdge MX740c EMC PowerEdge MX740c Installation and Service Manual - Page 97

M.2 BOSS module, Removing the M.2 BOSS module

Get Dell PowerEdge MX740c PDF manuals and user guides View all Dell PowerEdge MX740c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

Figure 69. Installing a MicroSD card Next steps 1. Install the IDSDM card. 2. Follow the procedure listed in After working inside your sled M.2 BOSS module The BOSS card is a simple RAID solution card which supports upto 2 M.2 SATA drives. The BOSS adapter card has a x8 connector using PCIe gen 2.0 x2 lanes, available only in the low-profile and half-height form factor. Removing the M.2 BOSS module Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 41. 2. Follow the procedure listed in Before working inside your sled on page 42. Steps Holding the blue tag, lift the M.2 BOSS module away from the system. Installing and removing system components 97

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Figure 69. Installing a MicroSD card
Next steps
1.
Install the IDSDM card
.
2.
Follow the procedure listed in
After working inside your sled
M.2 BOSS module
The BOSS card is a simple RAID solution card which supports upto 2 M.2 SATA drives. The BOSS adapter card has a x8
connector using PCIe gen 2.0 x2 lanes, available only in the low-profile and half-height form factor.
Removing the M.2 BOSS module
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 41.
2.
Follow the procedure listed in
Before working inside your sled
on page 42.
Steps
Holding the blue tag, lift the M.2 BOSS module away from the system.
Installing and removing system components
97