Dell PowerEdge MX740c EMC PowerEdge MX740c Installation and Service Manual - Page 82

Removing the processor from the processor and heat sink module

Get Dell PowerEdge MX740c PDF manuals and user guides View all Dell PowerEdge MX740c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Figure 51. Removing the processor and heat sink module ( PHM ) Next steps 1. Install the processor and heat sink module. Removing the processor from the processor and heat sink module Prerequisites 1. Follow the safety guidelines listed in Safety Instructions. 2. Follow the procedure listed in Before working inside your sled. 3. Remove the air shroud. 4. Remove the processor and heat sink module WARNING: The heat sink may be hot to touch for some time after the system has been powered down. Allow the heat sink to cool before removing it. . NOTE: This procedure is only needed when replacing a processor or heat sink. This is not needed when replacing system board. Steps 1. Place the heat sink with the processor side facing up. 2. Insert a flat blade screwdriver into the release slot marked with a yellow label. Twist (do not pry) the screwdriver to break the thermal paste seal. 3. Push the retaining clips on the processor bracket to unlock the bracket from the heat sink. 82 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Figure 51. Removing the processor and heat sink module ( PHM )
Next steps
1.
Install the processor and heat sink module
.
Removing the processor from the processor and heat sink module
Prerequisites
1.
Follow the safety guidelines listed in
Safety Instructions
.
2.
Follow the procedure listed in
Before working inside your sled
.
3.
Remove the air shroud
.
4.
Remove the processor and heat sink module
WARNING:
The heat sink may be hot to touch for some time after the system has been powered down. Allow
the heat sink to cool before removing it.
.
NOTE:
This procedure is only needed when replacing a processor or heat sink. This is not needed when replacing system
board.
Steps
1.
Place the heat sink with the processor side facing up.
2.
Insert a flat blade screwdriver into the release slot marked with a yellow label. Twist (do not pry) the screwdriver to break
the thermal paste seal.
3.
Push the retaining clips on the processor bracket to unlock the bracket from the heat sink.
82
Installing and removing system components