Dell PowerEdge R760XA Installation and Service Manual - Page 102

Lift up the TIM break lever, Removing the retaining clip

Get Dell PowerEdge R760XA PDF manuals and user guides View all Dell PowerEdge R760XA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

2. Using your thumb, lift up the Thermal Interface Material (TIM) break lever to release the processor from the TIM and retaining clip. 3. Holding the processor by the edges, lift the processor away from the retaining clip. NOTE: Ensure to hold the retaining clip to the heat sink as you lift the TIM break lever. Figure 63. Lift up the TIM break lever 4. Using your thumb and index finger, first hold the retaining clip release tab at the pin 1 connector, pull out the tip of the release tab, and then lift the retaining clip partially from the heat sink. NOTE: Ensure to return the TIM break lever back to its original position. 5. Repeat the above procedure at the remaining three corners of the retaining clip. 6. After all the corners are released from the heat sink, lift the retaining clip from the pin 1 corner of the heat sink. Figure 64. Removing the retaining clip 102 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
2.
Using your thumb, lift up the Thermal Interface Material (TIM) break lever to release the processor from the TIM and
retaining clip.
3.
Holding the processor by the edges, lift the processor away from the retaining clip.
NOTE:
Ensure to hold the retaining clip to the heat sink as you lift the TIM break lever.
Figure 63. Lift up the TIM break lever
4.
Using your thumb and index finger, first hold the retaining clip release tab at the pin 1 connector, pull out the tip of the
release tab, and then lift the retaining clip partially from the heat sink.
NOTE:
Ensure to return the TIM break lever back to its original position.
5.
Repeat the above procedure at the remaining three corners of the retaining clip.
6.
After all the corners are released from the heat sink, lift the retaining clip from the pin 1 corner of the heat sink.
Figure 64. Removing the retaining clip
102
Installing and removing system components