Dell PowerEdge R760XA Installation and Service Manual - Page 144

Installing the VGA port, Removing the VGA port

Get Dell PowerEdge R760XA PDF manuals and user guides View all Dell PowerEdge R760XA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 144 highlights

3. Disconnect the VGA port cable from the liquid cooling (LC) rear I/O board. 4. Open the latch on the expansion card riser and slide the VGA port out of the expansion card riser. Figure 112. Removing the VGA port 5. Install the filler bracket if not replacing the VGA port. Next steps 1. Replace the VGA port. Installing the VGA port Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the air shroud. NOTE: VGA port is supported only in slot 8 of the expansion card riser. Steps 1. Open the latch on the expansion card riser and remove the filler bracket from the expansion card riser. 2. Slide the VGA port into the expansion card riser and close the latch. 144 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
3.
Disconnect the VGA port cable from the liquid cooling (LC) rear I/O board.
4.
Open the latch on the expansion card riser and slide the VGA port out of the expansion card riser.
Figure 112. Removing the VGA port
5.
Install the filler bracket if not replacing the VGA port.
Next steps
1.
Replace the VGA port
.
Installing the VGA port
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Remove the air shroud
.
NOTE:
VGA port is supported only in slot 8 of the expansion card riser.
Steps
1.
Open the latch on the expansion card riser and remove the filler bracket from the expansion card riser.
2.
Slide the VGA port into the expansion card riser and close the latch.
144
Installing and removing system components