Dell PowerEdge R760XA Installation and Service Manual - Page 137

Next steps, Prerequisites, Steps, Installing the sponge

Get Dell PowerEdge R760XA PDF manuals and user guides View all Dell PowerEdge R760XA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 137 highlights

Figure 103. Installing the sponge Next steps 1. Install the rear mounting front PERC module. 2. Follow the procedure listed in After working inside your system. Removing the Bridge Cards Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the rear mounting front PERC module. NOTE: Observe the cable routing before disconnecting the cables. 4. Remove the sponges. 5. Remove the GPU riser module. 6. Number of bridge cards vary as per the GPU. 7. Slot priority for GPU card installation without bridge cards: slot 31, slot 36, slot 33, and slot 38. 8. Slot priority for GPU card installation with bridge cards: slot 31, slot 33, slot 36, and slot 38. NOTE: For more information about supported GPU cards and their slot priority, see expansion card installation guidelines. Steps 1. Holding the edges, pull the bridge cards out of the GPU cards. Installing and removing system components 137

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
Figure 103. Installing the sponge
Next steps
1.
Install the rear mounting front PERC module
.
2.
Follow the procedure listed in
After working inside your system
.
Removing the Bridge Cards
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the rear mounting front PERC module
.
NOTE:
Observe the cable routing before disconnecting the cables.
4.
Remove the sponges
.
5.
Remove the GPU riser module
.
6.
Number of bridge cards vary as per the GPU.
7.
Slot priority for GPU card installation without bridge cards: slot 31, slot 36, slot 33, and slot 38.
8.
Slot priority for GPU card installation with bridge cards: slot 31, slot 33, slot 36, and slot 38.
NOTE:
For more information about supported GPU cards and their slot priority, see
expansion card installation guidelines
.
Steps
1.
Holding the edges, pull the bridge cards out of the GPU cards.
Installing and removing system components
137