Home » Epson Manuals » Photo Printers » Epson R260 » Manual Viewer

Epson R260 Service Manual - Page 104

CR Unit, Reinstalling the LD Roller

UPC - 010343859043

Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

EPSON Stylus Photo R260/R265/R270, R360/R380/R390 7. Remove the Combination Gear (10, 15.2), and remove the ASF Unit. Combination Gear Removal Direction [Rear side] Figure 4-143. Removing the ASF Unit ASF Unit „ Lubrication is required. See the page given below for the lubrication information. "6.1.3 Lubrication (p.131)" „ When installing the ASF Unit, make sure that the Combination Gear, tip of the Change Lever and the two hooks are securely attached. Also make sure that there is appropriate space at both the left and right of the Change Lever. „ Tighten the screws in the order given in Fig.4-141. „ Install the LD Roller following the procedure below. Make sure to apply grease referring to the page given below. "6.1.3 Lubrication (p.131)" Install the LD Roller aligning the arrow on the LD Roller with the arrow on the blade of the shaft. Make sure the LD Roller is securely attached without gap or misalignment. Align the arrows LD Roller ASF Unit Revision B 4.5.12 CR Unit † Parts/Components need to be removed in advance All exterior parts/ All control boards / Middle Housing / Printer Mechanism / CR Scale / APG Unit / CR Motor / EJ Frame Assy † Removal procedure CHECK P O IN T Refer to the Orientation Definition below for the directions indicated in the following procedures. •"4.1.6 Orientation Definition (p.61)" C A U T IO N Before turning the Parallelism Bushing L, mark the scale position of the Parallelism Bushing with a marker. And taking extra care not to damage the Gear with the rib, pull it toward the front. 1. Disengage the upper end of the Spring (1) from the slit, and remove the Spring (1). 2. Loosen the screw ( ), and turn the Parallelism Bushing L clockwise to the maximum. Spring (1) Slit Parallelism Bushing L Blade LD Roller Shaft Figure 4-144. Reinstalling the LD Roller Figure 4-145. Removing the CR Unit (1) Disassembly/Assembly Disassembly of the Printer Mechanism 105

Section	Page
Cover Page-Service	1
Product description	7
1.1 Overview	8
1.1.1 Differences between R260/265/270 and R360/380/390	8
1.2 Basic Specifications	9
1.2.1 Printing	9
1.2.2 Interfaces	10
1.3 Standalone Printing (R360/R380/R390 only)	12
1.3.1 Direct Print of Still Images	12
1.3.2 Direct Print of Movie Frames	13
1.4 Backup Function (R360/R380/R390 only)	14
1.5 CD/DVD Print (R360/R380/R390 only)	17
1.6 Operation Panel	18
1.6.1 Operation Panel	18
1.6.2 Indicator (LED)	19
1.7 Specifications Common to the Models	20
1.7.1 Electric Specifications	20
1.7.2 Environmental Condition	20
1.7.3 Durability	20
1.7.4 Noise Level	20
1.7.5 Dimensions	21
Operating Principles	22
2.1 Overview	23
2.1.1 Printer Mechanism	23
2.1.2 Motors & Sensors	24
2.2 Electrical Circuit Operating Principles	25
2.2.1 Main Features	25
2.2.2 Components of Control Boards	26
2.2.3 Circuit Block Diagram	27
2.3 Banding Reduction System (BRS) / Paper Feed Amount Profile Correction (PFP)	29
Troubleshooting	30
3.1 Overview	31
3.1.1 Troubleshooting on Motors and Sensors	31
3.2 Error/Warning Indications	32
3.2.1 Error Indication Method	32
3.3 Troubleshooting by Error Message	35
3.3.1 Troubleshooting Problems with Error Messages	35
3.4 Troubleshooting by Symptom	47
3.4.1 Problems in Printing Operation	47
3.4.2 Power Problems	52
3.4.3 Ink-related Problems	52
3.4.4 Problems with Interfaces	54
Disassembly/Assembly	55
4.1 Overview	56
4.1.1 Precautions	56
4.1.2 Tools	57
4.1.3 Screws	57
4.1.4 Work Completion Checklist	58
4.1.5 Required Preparation before Disassembly	60
4.1.6 Orientation Definition	60
4.1.7 How to Unlock the Carriage	61
4.1.8 Sharp Metal Edges (Danger!)	61
4.1.9 Differences in Disassembly Procedure by Model	62
4.1.10 Disassembly/Assembly Procedures	63
4.2 Removing Exterior Parts/Components	64
4.2.1 Paper Support	64
4.2.2 Printer Cover	64
4.2.3 Front Cover	65
4.2.4 Right Housing / Left Housing / USB Housing	65
4.2.5 Upper Housing	67
4.2.6 Panel Unit	68
4.2.7 EMI Frame / Waste Ink Tray	69
4.2.8 Right Front Housing / Left Front Housing	71
4.2.9 Front Housing	72
4.3 Removing Control Boards	75
4.3.1 Removing the USB Board (R260/R265/R270 only)	75
4.3.2 Removing the Main Board Unit	77
4.3.3 Disassembling the Main Board Unit	79
4.3.4 Removing the Card Board (R360/R380/R390 only)	81
4.3.5 Disassembling the Panel Unit	82
4.3.6 Middle Housing	85
4.4 Removing the Printer Mechanism	86
4.4.1 Removing the Printer Mechanism	86
4.5 Disassembly of the Printer Mechanism	88
4.5.1 CR Scale	88
4.5.2 APG Unit	89
4.5.3 Printhead	90
4.5.4 Waste Ink Pad	93
4.5.5 P/S Assy	93
4.5.6 Stacker Assy	94
4.5.7 Ink System	96
4.5.8 CR Motor	98
4.5.9 EJ Frame Assy	99
4.5.10 PF Encoder / PF Scale / PF Motor	101
4.5.11 ASF Unit	103
4.5.12 CR Unit	104
4.5.13 Upper Paper Guide	107
4.5.14 Front Paper Guide Assy/APG Sensor Assy	108
4.5.15 CDR Guide Detection Assy	110
Adjustment	111
5.1 Adjustment Items and Overview	112
5.1.1 Servicing Adjustment Item List	112
5.1.2 Replacement Part Adjustment Items	115
5.2 Adjustment by Using Adjustment Program	117
5.2.1 Top Margin Adjustment	117
5.2.2 Head angular adjustment	117
5.2.3 Bi-D Adjustment	118
5.2.4 PW Adjustment/First Dot Adjustment	119
5.2.5 PF Adjustment	120
5.2.6 PG Adjustment	121
5.3 Banding Reduction System (BRS) Adjustment/ Paper Feed Amount Profile (PFP) Correction	123
5.3.1 Overview	123
5.3.2 Adjustment Procedure	124
Maintenance	128
6.1 Overview	129
6.1.1 Cleaning	129
6.1.2 Service Maintenance	129
6.1.3 Lubrication	130
Appendix	136
7.1 Exploded Diagram / Parts List	137