Epson R260 Service Manual - Page 95

remove the Left Stacker Guide. Also remove the Right Stacker Guide in

Get Epson R260 - Stylus Photo Color Inkjet Printer PDF manuals and user guides
UPC - 010343859043
View all Epson R260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4. Follow the steps below to remove the CDR Guide Lever Spring. 1) Pull the end A toward you. 2) Pull the end B out of the notch. 3) Pull the end A out of the shaft, and remove the CDR Guide Lever Spring. 2 A B 1 A CDR Shaft 3 Figure 4-110. Removing the CDR Guide Lever Spring (2) 5. Remove the four screws that secure the Stacker Assy. • Screw : C.B.P. M3x8 (tightening torque: 5-7 kgf.cm) (The numbers shown in the figure indicate the order of tightening the screws.) 6. Holding the Left/Right Stacker Guides, remove the Stacker Assy from the Lower Housing. 3 4 1 2 Stacker Assy Left Stacker Guide Right Stacker Guide Figure 4-111. Removing the Stacker Assy Revision B 7. While disengaging the hook, remove the left gear from the CDR Shaft and remove the Left Stacker Guide. Also remove the Right Stacker Guide in the same way. 8. Remove the CDR Shaft from the Stacker. Left Stacker Guide : Hook [Right side] CDR Shaft [Left side] Right Stacker Guide Figure 4-112. Removing the CDR Shaft „ Lubrication is required. See the page given below for the lubrication information. "6.1.3 Lubrication (p.131)" „ Install the CDR Shaft so that one of its gear holes further to the shaft end goes to the left (the spring attached side). „ When attaching the CDR Shaft, make sure to match the phases of the left and right gears as shown below. • Insert the gear tooth with a small protrusion on its root into the groove between the 3rd and 4th teeth of the Stacker Guide Left/Right. Right Stacker Guide CDR Shaft 3 4 Tooth with protrusion Figure 4-113. Reinstalling the CDR Shaft Disassembly/Assembly Disassembly of the Printer Mechanism 96

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
EPSON Stylus Photo R260/R265/R270, R360/R380/R390
Revision B
Disassembly/Assembly
Disassembly of the Printer Mechanism
96
4.
Follow the steps below to remove the CDR Guide Lever Spring.
1) Pull the end A toward you.
2) Pull the end B out of the notch.
3) Pull the end A out of the shaft, and remove the CDR Guide Lever Spring.
Figure 4-110.
Removing the CDR Guide Lever Spring (2)
5.
Remove the four screws that secure the Stacker Assy.
•
Screw
: C.B.P. M3x8 (tightening torque: 5-7 kgf.cm)
(The numbers shown in the figure indicate the order of tightening the screws.)
6.
Holding the Left/Right Stacker Guides, remove the Stacker Assy from the
Lower Housing.
Figure 4-111.
Removing the Stacker Assy
7.
While disengaging the hook, remove the left gear from the CDR Shaft and
remove the Left Stacker Guide. Also remove the Right Stacker Guide in the
same way.
8.
Remove the CDR Shaft from the Stacker.
Figure 4-112.
Removing the CDR Shaft
1
A
CDR Shaft
2
3
B
A
1
2
3
4
Left Stacker Guide
Stacker Assy
Right Stacker Guide
Lubrication is required. See the page given below for the
lubrication information.
"6.1.3 Lubrication (p.131)"
Install the CDR Shaft so that one of its gear holes further to the
shaft end goes to the left (the spring attached side).
When attaching the CDR Shaft, make sure to match the phases
of the left and right gears as shown below.
•
Insert the gear tooth with a small protrusion on its root into
the groove between the 3rd and 4th teeth of the Stacker
Guide Left/Right.
Figure 4-113.
Reinstalling the CDR Shaft
Right Stacker Guide
Left Stacker Guide
[Left side]
[Right side]
CDR
Shaft
: Hook
3
4
CDR Shaft
Tooth with protrusion
Right Stacker Guide