Epson R260 Service Manual - Page 88

Disassembly of the Printer Mechanism, 4.5.1 CR Scale, CR Scale

Get Epson R260 - Stylus Photo Color Inkjet Printer PDF manuals and user guides
UPC - 010343859043
View all Epson R260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4.5 Disassembly of the Printer Mechanism 4.5.1 CR Scale C A U T IO N „ Take extra care to avoid injury from sharp metal edges. Before starting, see the page given below to check the dangerous edges. • "4.1.8 Sharp Metal Edges (Danger!)" (p.62) „ During the disassembly/reassembly of the Printer Mechanism, take extra care not to touch the CR Scale with bare hands, and not to contaminate or scratch it. † Parts/Components need to be removed in advance All exterior parts/ All control boards / Middle Housing † Removal procedure CHECK P O IN T „ See the section given below on how to unlock the carriage. • "4.1.7 How to Unlock the Carriage (p.62)" „ Refer to the Orientation Definition below for the directions indicated in the following procedures. • "4.1.6 Orientation Definition (p.61)" Revision B 1. Unlock the carriage and move the CR Unit to the center. 2. Remove the Torsion Spring from the hook ( ) on the left side of the Main Frame. 3. Remove the CR Scale from the hook ( ) on the right side of the Main Frame. 4. Pull out the CR Scale from the slit of the CR Unit. 5. Turn the CR Scale 90 degrees in the direction of the arrow, and remove the CR Scale from the hook. Torsion Spring Slit Hook Turn 90° CR Scale Figure 4-88. Removing the CR Scale Install the CR Scale with its cut-corner facing upward. Hitch one end of the Torsion Spring to the hole of the CR Scale from the rear side of the printer. Hitch from the rear side Cut-corner Disassembly/Assembly Figure 4-89. Reinstalling the CR Scale Disassembly of the Printer Mechanism Hook 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
EPSON Stylus Photo R260/R265/R270, R360/R380/R390
Revision B
Disassembly/Assembly
Disassembly of the Printer Mechanism
89
4.5
Disassembly of the Printer Mechanism
4.5.1
CR Scale
Parts/Components need to be removed in advance
All exterior parts/ All control boards / Middle Housing
Removal procedure
1.
Unlock the carriage and move the CR Unit to the center.
2.
Remove the Torsion Spring from the hook (
) on the left side of the Main
Frame.
3.
Remove the CR Scale from the hook (
) on the right side of the Main
Frame.
4.
Pull out the CR Scale from the slit of the CR Unit.
5.
Turn the CR Scale 90 degrees in the direction of the arrow, and remove the
CR Scale from the hook.
Figure 4-88.
Removing the CR Scale
Figure 4-89.
Reinstalling the CR Scale
C
A
U
T
I
O
N
Take extra care to avoid injury from sharp metal edges. Before
starting, see the page given below to check the dangerous edges.
•
“4.1.8 Sharp Metal Edges (Danger!)” (p.62)
During the disassembly/reassembly of the Printer Mechanism,
take extra care not to touch the CR Scale with bare hands, and
not to contaminate or scratch it.
C
H
E
C
K
P
O
I
N
T
See the section given below on how to unlock the carriage.
•
“4.1.7 How to Unlock the Carriage (p.62)”
Refer to the Orientation Definition below for the directions
indicated in the following procedures.
•
“4.1.6 Orientation Definition (p.61)”
Install the CR Scale with its cut-corner facing upward. Hitch one
end of the Torsion Spring to the hole of the CR Scale from the rear
side of the printer.
CR Scale
Turn 90
°
Torsion Spring
Slit
Hook
Cut-corner
Hitch from the rear side
Hook