Epson R260 Service Manual - Page 84

Attaching the FFC 1, FFC 2 R360/R380/R390, Removing the SW Buttons R260/R265/R270

Get Epson R260 - Stylus Photo Color Inkjet Printer PDF manuals and user guides
UPC - 010343859043
View all Epson R260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4. Remove the SW Button (1)(2)(3) and the LED Light Guide Plate. 123 LED Light Guide Plate Figure 4-76. Removing the SW Buttons (R260/R265/R270) 5. Peel off the double-sided tape and remove the two FFCs from the Shield Plate PNL. • Double-sided tape: Shield Plate PNL FFC Line marked on the plate Revision B „ When attaching the SW Buttons, insert their guide pin into the corresponding positioning hole firmly. After installing the Shield Plate PNL, check the buttons for clicking operability by pressing each of them. Following instructions are for R360/R380/R390 only „ When installing the LCD Panel, check that the inner side of the LCD Cover is free of dust or dirt. „ Install the Shield Plate PNL putting it under the cables connecting the two Panel Boards. „ When installing the FFC (1) to the Shield Plate PNL, align the FFC edges with the line marked on the panel, and secure it with double-sided tape. And when installing the FFC (2), fold the FFC and secure it with double-sided tape as shown below. FFC (1) FFC (2) Figure 4-77. Removing the FFC (R260/R265/R270) „ For the R260/R265/R270, when installing the FFC to the Shield Plate PNL, align the FFC edges with the lines marked on the plate as shown in Fig.4-77, and secure it with double-sided tape. When screwing the Panel Board Assy, tighten the screws in the order given in Fig.4-74. „ For the R260/R265/R270, screw the Panel Board in the order given in Fig.4-75. Line marked on the plate Figure 4-78. Attaching the FFC (1), FFC (2) (R360/R380/R390) „ Attach 40mm-length acetate tape referring to Fig.4-68. C A U T IO N When cleaning the LCD, do not use liquid type cleaner. The use of such cleaner may cause the coating film on the surface to come off. To clean the LCD, use a blower to blow off dust. Disassembly/Assembly Removing Control Boards 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
EPSON Stylus Photo R260/R265/R270, R360/R380/R390
Revision B
Disassembly/Assembly
Removing Control Boards
85
4.
Remove the SW Button (1)(2)(3) and the LED Light Guide Plate.
Figure 4-76.
Removing the SW Buttons (R260/R265/R270)
5.
Peel off the double-sided tape and remove the two FFCs from the Shield Plate
PNL.
•
Double-sided tape:
Figure 4-77.
Removing the FFC (R260/R265/R270)
For the R260/R265/R270, when installing the FFC to the Shield
Plate PNL, align the FFC edges with the lines marked on the
plate as shown in
Fig.4-77
, and secure it with double-sided
tape. When screwing the Panel Board Assy, tighten the screws
in the order given in
Fig.4-74
.
For the R260/R265/R270, screw the Panel Board in the order
given in
Fig.4-75
.
2
3
1
LED Light Guide Plate
FFC
Shield Plate PNL
Line marked on
the plate
When attaching the SW Buttons, insert their guide pin into the
corresponding positioning hole firmly. After installing the
Shield Plate PNL, check the buttons for clicking operability by
pressing each of them.
Following instructions are for R360/R380/R390 only
When installing the LCD Panel, check that the inner side of the
LCD Cover is free of dust or dirt.
Install the Shield Plate PNL putting it under the cables
connecting the two Panel Boards.
When installing the FFC (1) to the Shield Plate PNL, align the
FFC edges with the line marked on the panel, and secure it
with double-sided tape. And when installing the FFC (2), fold
the FFC and secure it with double-sided tape as shown below.
Figure 4-78.
Attaching the FFC (1), FFC (2) (R360/R380/R390)
Attach 40mm-length acetate tape referring to
Fig.4-68
.
C
A
U
T
I
O
N
When cleaning the LCD, do not use liquid type cleaner. The use of
such cleaner may cause the coating film on the surface to come off.
To clean the LCD, use a blower to blow off dust.
FFC (1)
FFC (2)
Line marked on the plate