HP GbE2c HP GbE2c Ethernet Blade Switch for c-Class BladeSystem ISCLI Referenc - Page 111

Default Gateway configuration, no enable, no interface ip, ip gateway, address, interval, retry

Get HP GbE2c - Blc Layer 2/3 Fiber SFP Option PDF manuals and user guides
UPC - 808736802215
View all HP GbE2c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 111 highlights

Table 118 IP Interface Configuration commands Command no enable no interface ip {} show interface ip {} Description Disables this IP interface. Command mode: Interface IP Removes this IP interface. Command mode: Global configuration Displays the current interface settings. Command mode: All NOTE: If you enter an IP address for interface 1, you are prompted to change the BOOTP setting. Default Gateway configuration The switch supports up to four gateways. By default, no gateways are configured on the switch. Enter 1, 2, 3, or 4 in the command as the , depending upon which gateway you want to configure. The following table describes the Default IP Gateway Configuration commands. Table 119 Default IP Gateway Configuration commands Command Description ip gateway {} address {} notation. Command mode: Global configuration ip gateway {} interval {} The switch pings the default gateway to verify that it is up. This option sets the time between health checks. The range is from 0 to 60 seconds. The default is 2 seconds. Command mode: Global configuration ip gateway {} retry {} Sets the number of failed health check attempts required before declaring this default gateway inoperative. The range is from 1 to 120 attempts. The default is 8 attempts. Command mode: Global configuration [no] ip gateway {} arphealth-check Enables or disables Address Resolution Protocol (ARP) health checks. This command is disabled by default. Command mode: Global configuration ip gateway {} enable Enables the gateway for use. Command mode: Global configuration no ip gateway {} enable Disables the gateway. Command mode: Global configuration no ip gateway {} Deletes the gateway from the configuration. Command mode: Global configuration show ip gateway {} Displays the current gateway settings. Command mode: All except User EXEC Configuration Commands 111

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
Configuration Commands 111
Table 118
IP Interface Configuration commands
Command
Description
no enable
Disables this IP interface.
Command mode
: Interface IP
no interface ip {
<1-256>
}
Removes this IP interface.
Command mode
: Global configuration
show interface ip {
<1-256>
}
Displays the current interface settings.
Command mode
: All
NOTE:
If you enter an IP address for interface 1, you are prompted to change the BOOTP setting.
Default Gateway configuration
The switch supports up to four gateways. By default, no gateways are configured on the switch. Enter 1, 2, 3, or 4 in
the command as the
<gateway instance>
, depending upon which gateway you want to configure.
The following table describes the Default IP Gateway Configuration commands.
Table 119
Default IP Gateway Configuration commands
Command
Description
ip gateway {
<1-4>
} address {
<IP
address>
}
Configures the IP address of the default IP gateway using dotted decimal
notation.
Command mode
: Global configuration
ip gateway {
<1-4>
} interval
{
<0-60>
}
The switch pings the default gateway to verify that it is up. This option sets
the time between health checks. The range is from 0 to 60 seconds. The
default is 2
seconds.
Command mode
: Global configuration
ip gateway {
<1-4>
} retry {
<1-
120>
}
Sets the number of failed health check attempts required before declaring
this default gateway inoperative. The range is from 1 to 120 attempts. The
default is 8 attempts.
Command mode
: Global configuration
[no] ip gateway {
<1-4>
} arp-
health-check
Enables or disables Address Resolution Protocol (ARP) health checks. This
command is disabled by default.
Command mode
: Global configuration
ip gateway {
<1-4>
} enable
Enables the gateway for use.
Command mode
: Global configuration
no ip gateway {
<1-4>
} enable
Disables the gateway.
Command mode
: Global configuration
no ip gateway {
<1-4>
}
Deletes the gateway from the configuration.
Command mode
: Global configuration
show ip gateway {
<1-4>
}
Displays the current gateway settings.
Command mode
: All except User EXEC