HP LH4r HP Netserver LH 3000 Installation Guide - Page 110

Left Rear, Rack Column, Rear of NetServer, Cable Management Arm

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

Chapter 8 Installing the HP NetServer in the HP Rack System/E or Rack System/U Rear of NetServer Left Rear Rack Column Cable Management Arm Figure 8-16. Attaching the Cable Management Arm 1. Ensure the HP NetServer is pushed all the way into the rack. 2. At the rear of the NetServer, place rack nuts on the left column in the 17th and 18th holes above the baseline of the HP NetServer. See Figure 8-16. 3. Install the two 6-32 pan head Torx 15 screws in the two threaded holes on the rear of the NetServer. 4. Orient the cable management arm as shown in Figure 8-16. 5. Install the flange over the 6-32 screws and tighten them. 6. Attach the other flange of the cable arm to the rear column of the rack with the two M-5 pan head Torx 25 screws, included with the arm. 7. Extend the HP NetServer out of the rack to ensure the Cable Management Arm moves with the chassis without binding. 8. Slide the HP NetServer back into the rack. 9. At the front of the rack, insert the screws through the flanges into the rack nuts and secure the HP NetServer to the front rack columns with a Torx 25 driver. 102

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Chapter 8
Installing the HP NetServer in the HP Rack System/E or Rack System/U
102
Left Rear
Rack Column
Rear of NetServer
Cable Management Arm
Figure 8-16. Attaching the Cable Management Arm
1.
Ensure the HP NetServer is pushed all the way into the rack.
2.
At the rear of the NetServer, place rack nuts on the left column in the 17th
and 18th holes above the baseline of the HP NetServer. See Figure 8-16.
3.
Install the two 6-32 pan head Torx 15 screws in the two threaded holes on
the rear of the NetServer.
4.
Orient the cable management arm as shown in Figure 8-16.
5.
Install the flange over the 6-32 screws and tighten them.
6.
Attach the other flange of the cable arm to the rear column of the rack with
the two M-5 pan head Torx 25 screws, included with the arm.
7.
Extend the HP NetServer out of the rack to ensure the Cable Management
Arm moves with the chassis without binding.
8.
Slide the HP NetServer back into the rack.
9.
At the front of the rack, insert the screws through the flanges into the rack
nuts and secure the HP NetServer to the front rack columns with a Torx 25
driver.