HP LH4r HP Netserver LH 3000 Installation Guide - Page 137

SCSI Configuration Utility

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 137 highlights

Chapter 10 Configuring the HP NetServer SCSI Configuration Utility NOTE The Symbios Configuration Utility is not available if you leave the NetRAID default unchanged. It is only available for LVD SCSI mode. If you need to verify or modify SCSI host adapter settings, or if you need to low-level format SCSI disks or verify SCSI disk media, run the Symbios Configuration utility: 1. Turn on or reboot your system. 2. During system start-up or reset, when the following message appears, press the [CTRL] and [C] keys at the same time. Press [Ctrl] [C] to start Symbios Configuration Utility 3. Use the arrow keys to move the cursor, press Enter to select an option, and press Esc to exit. 4. To change adapter settings: ◊ Select an adapter from the list in the main menu. ◊ Select Adapter Setup. This option configures the SCSI ID setting and other advanced adapter settings. 5. To format a hard disk or change hard disk parameters: ◊ Select an adapter from the list in the main menu. ◊ Select Device Selections. ◊ Select the hard disk to format. ◊ Select Format menu option. 129

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Chapter 10
Configuring the HP NetServer
129
SCSI Configuration Utility
NOTE
The Symbios Configuration Utility is not available if you leave
the NetRAID default unchanged. It is only available for LVD
SCSI mode.
If you need to verify or modify SCSI host adapter settings, or if you need to
low-level format SCSI disks or verify SCSI disk media, run the Symbios
Configuration utility:
1.
Turn on or reboot your system.
2.
During system start-up or reset, when the following message appears, press
the [
CTRL
] and [
C
] keys at the same time.
Press [Ctrl] [C] to start Symbios
Configuration Utility
3.
Use the arrow keys to move the cursor, press
Enter
to select an option, and
press
Esc
to exit.
4.
To change adapter settings:
◊
Select an adapter from the list in the main menu.
◊
Select
Adapter Setup
. This option configures the SCSI ID setting and
other advanced adapter settings.
5.
To format a hard disk or change hard disk parameters:
◊
Select an adapter from the list in the main menu.
◊
Select
Device Selections
.
◊
Select the hard disk to format.
◊
Select
Format
menu option.