HP LH4r HP Netserver LH 3000 Installation Guide - Page 61

Installing Additional Memory

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

5 Installing Additional Memory Introduction This chapter describes adding memory to the HP NetServer LH 3000r and LH 3000. The standard configuration ships with one 128 MB DIMM in slot 0. DIMM Socket 0 DIMM Socket 1 DIMM Socket 2 DIMM Socket 3 Figure 5-1. DIMM Sockets on System Board Assembly Memory Guidelines l Add DIMMs of these sizes: ◊ 128 Mb ◊ 256 Mb ◊ 512 Mb ◊ 1 GB l Add memory in any order to the four slots. l You can mix DIMM sizes. For example, you may place a 1 GB DIMM next to a 128 Mb DIMM. l Maximum configuration is 4 GB. l Do not rock the DIMM into place, but apply firm and even pressure until it is seated in the socket. l Use only HP-supported DIMMs. NOTE If non-HP DIMMs are used, the NetServer will report this during boot. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
53
5
Installing Additional Memory
Introduction
This chapter describes adding memory to the HP NetServer LH 3000r and
LH 3000. The standard configuration ships with one 128 MB DIMM in slot 0.
DIMM Socket
0
DIMM Socket
2
DIMM Socket
1
DIMM Socket
3
Figure 5-1. DIMM Sockets on System Board Assembly
Memory Guidelines
Add DIMMs of these sizes:
◊
128 Mb
◊
256 Mb
◊
512 Mb
◊
1 GB
Add memory in any order to the four slots.
You can mix DIMM sizes. For example, you may place a 1 GB DIMM
next to a 128 Mb DIMM.
Maximum configuration is 4 GB.
Do not rock the DIMM into place, but apply firm and even pressure until it
is seated in the socket.
Use only HP-supported DIMMs.
NOTE
If non-HP DIMMs are used, the NetServer will report this
during boot.