HP LH4r HP Netserver LH 3000 Installation Guide - Page 155

Marking Rear Columns

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 155 highlights

Chapter 13 Alternative Rack Mounting Marking Rear Columns 5. Mark the slide mounting holes on the inside faces of the rear columns. 6. Mark the baseline (bottom) of the NetServer at an EIA unit mark on the column. 7. Hold the bottom of the rack template at the baseline. Mark the top of NetServer (8 EIA units counted up from the baseline). 8. Mark the slide mounting hole (hole 21 counted up from the baseline). 9. Mark the second rear column by repeating steps 5 through 8. Use the template to measure, or count up 21 from baseline on inside face for rear slide mounts. Template p/n 50645869 The inside face is the one inside the rack (at 90 degrees to you when you open the rack door). The slides fasten behind the outside face of the front of the rack, at the 22nd and 20th holes above the unit below. Base line Figure 13-2. Marking the Rack Columns 147

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Chapter 13
Alternative Rack Mounting
147
Marking Rear Columns
5.
Mark the slide mounting holes on the inside faces of the rear columns.
6.
Mark the baseline (bottom) of the NetServer at an EIA unit mark on the
column.
7.
Hold the bottom of the rack template at the baseline. Mark the top of
NetServer (8 EIA units counted up from the baseline).
8.
Mark the slide mounting hole (hole 21 counted up from the baseline).
9.
Mark the second rear column by repeating steps 5 through 8.
Use the template to
measure, or count up
21 from baseline on inside
face for rear slide mounts.
Base line
Template
p/n
5064-
5869
The inside face
is the one inside
the rack (at 90
degrees to you
when you
open the
rack door).
The slides
fasten
behind
the outside
face of the
front of
the rack,
at the
22nd and
20th holes
above the
unit below.
Figure 13-2. Marking the Rack Columns