HP LH4r HP Netserver LH 3000 Installation Guide - Page 150

Password Problems

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 150 highlights

Chapter 12 Troubleshooting 4. Plug in the power cord and turn on power to the HP NetServer. The following message appears: The configuration has been cleared. Set the Clear Config switch to the OFF position before rebooting. 5. Turn off power to the HP NetServer and unplug the power cord. 6. Return switch 5 on the system board to the OFF position. 7. Replace the top cover and the front bezel, then plug in the power cord. 8. Turn on power to the HP NetServer. The error message may be displayed: 0012-34 : Incorrect System Configuration 9. Press the [F2] function key and answer Yes to save the configuration, then exit the Setup utility. Password Problems If you have forgotten the password, your HP NetServer will function normally, but you will not be able to change the system configuration settings in the Setup utility. To reset the password: 1. For rack-mount and pedestal models, follow the instructions in Chapter 3, "Opening and Closing the HP NetServer," to gain access to the server. 2. Turn off power to the HP NetServer and unplug the power cord. 3. Refer to Figure 12-1 and move switch 6 on the system board (labeled " Clear Password") to the ON position. 4. Plug in the power cord. Turn on power to the HP NetServer, and allow it to complete its startup routing. The old password will be erased. 5. Turn off power to the HP NetServer. Unplug the power cord. 6. Return switch 6 to the OFF position. 7. Replace Cover 2 and the bezel. 8. Plug in the power cord. Turn on power to the HP NetServer and allow it to complete its startup routine. 9. If you wish to set the password again, during the power-on system hardware test press the [F2] function key to start the Setup utility. 10. Set the new password in the Security menu. 11. Press the [F10] function key and answer Yes to save the configuration, including the new password. 142

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Chapter 12
Troubleshooting
142
4.
Plug in the power cord and turn on power to the HP NetServer. The
following message appears:
The configuration has been cleared. Set the
Clear Config switch to the OFF position
before rebooting.
5.
Turn off power to the HP NetServer and unplug the power cord.
6.
Return switch 5 on the system board to the OFF position.
7.
Replace the top cover and the front bezel, then plug in the power cord.
8.
Turn on power to the HP NetServer. The error message may be displayed:
0012-34 :
Incorrect System Configuration
9.
Press the [
F2
] function key and answer
Yes
to save the configuration,
then exit the Setup utility.
Password Problems
If you have forgotten the password, your HP NetServer will function normally,
but you will not be able to change the system configuration settings in the Setup
utility. To reset the password:
1.
For rack-mount and pedestal models, follow the instructions in Chapter 3,
"Opening and Closing the HP NetServer," to gain access to the server.
2.
Turn off power to the HP NetServer and unplug the power cord.
3.
Refer to Figure 12-1 and move switch 6 on the system board (labeled "
Clear Password") to the ON position.
4.
Plug in the power cord. Turn on power to the HP NetServer, and allow it to
complete its startup routing. The old password will be erased.
5.
Turn off power to the HP NetServer. Unplug the power cord.
6.
Return switch 6 to the OFF position.
7.
Replace Cover 2 and the bezel.
8.
Plug in the power cord. Turn on power to the HP NetServer and allow it to
complete its startup routine.
9.
If you wish to set the password again, during the power-on system
hardware test press the [
F2
] function key to start the Setup utility.
10.
Set the new password in the Security menu.
11.
Press the [
F10
] function key and answer
Yes
to save the configuration,
including the new password.