HP LH4r HP Netserver LH 3000 Installation Guide - Page 71

Controls, Ports, and Indicators.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Chapter 6 Installing Additional PCI Boards 1. Read the documentation included with each board and follow any special instructions provided. 2. If necessary, log off all users and gracefully shut down the network operating system according to directions in your NOS documentation. 3. Make sure the HP NetServer is powered off according to the instructions in Chapter 2, "Controls, Ports, and Indicators." 4. Disconnect the power cord and cables, and label each one to support reassembly. CAUTION The power supplies will continue to provide standby current to the NetServer until the power cable is disconnected. 5. For rack-mount and pedestal models, follow the instructions in Chapter 3, "Opening and Closing the HP NetServer," to gain access to the server. 6. Consider the boot priority before installing any accessory boards. For details, refer to the topic "Boot Priority" earlier in this chapter. If installing a SCSI controller board, the controller's priority (boot order) is set by the board's slot location. 7. Identify the desired slot (P1 through P8) before installing the accessory board. In this example, non-hot-plug Slot 3 is used. NOTE Slots are keyed to prevent a +5 volt board from going into a 3.3 volt slot. 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Chapter 6
Installing Additional PCI Boards
63
1.
Read the documentation included with each board and follow any special
instructions provided.
2.
If necessary, log off all users and gracefully shut down the network
operating system according to directions in your NOS documentation.
3.
Make sure the HP NetServer is powered off according to the instructions in
Chapter 2, "Controls, Ports, and Indicators."
4.
Disconnect the power cord and cables, and label each one to support re-
assembly.
CAUTION
The power supplies will continue to provide standby current to
the NetServer until the power cable is disconnected.
5.
For rack-mount and pedestal models, follow the instructions in Chapter 3,
"Opening and Closing the HP NetServer," to gain access to the server.
6.
Consider the boot priority before installing any accessory boards.
For details, refer to the topic "Boot Priority" earlier in this chapter. If
installing a SCSI controller board, the controller’s priority (boot order) is
set by the board’s slot location.
7.
Identify the desired slot (P1 through P8) before installing the accessory
board. In this example, non-hot-plug Slot 3 is used.
NOTE
Slots are keyed to prevent a +5 volt board from going into a 3.3
volt slot.