HP LH4r HP Netserver LH 3000 Installation Guide - Page 57

Removing a Hot-Swap Hard Disk Drive Module

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Chapter 4 Installing Mass Storage Devices NOTE Closing the ejector handle engages the drive with the electrical connector in the hot-swap mass storage cage and seats the drive. 7. If the drive is unseated in the cage after closing the ejector handle, repeat steps 5 and 6. 8. Configure mass storage devices according to Chapter 10, "Configuring the HP NetServer." Removing a Hot-Swap Hard Disk Drive Module CAUTION You must remove the drive slowly to ensure the drive heads are parked prior to removal. Follow these instructions to prevent handling damage, such as head slaps or head actuator unlocking. 1. To unlock the drive, push the locking latch in and then pull the ejector handle toward you. See Figure 4-15. 2. Gently pull the drive out about an inch to disengage the power connection. 3. Wait about 30 seconds for the drive to stop spinning and the drive heads to park. 4. Use your hand to support the bottom of the drive, while you slowly pull the drive straight out. Do not allow the drive to fall. 5. Place the drive in an electrostatic-protected container. Do not stack drives. 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Chapter 4
Installing Mass Storage Devices
49
NOTE
Closing the ejector handle engages the drive with the electrical
connector in the hot-swap mass storage cage and seats the
drive.
7.
If the drive is unseated in the cage after closing the ejector handle, repeat
steps 5 and 6.
8.
Configure mass storage devices according to Chapter 10, "Configuring the
HP NetServer."
Removing a Hot-Swap Hard Disk Drive Module
CAUTION
You must remove the drive slowly to ensure the drive heads
are parked prior to removal.
Follow these instructions to
prevent handling damage, such as head slaps or head actuator
unlocking.
1.
To unlock the drive, push the locking latch in and then pull the ejector
handle toward you.
See Figure 4-15.
2.
Gently pull the drive out about an inch to disengage the power connection.
3.
Wait about 30 seconds for the drive to stop spinning and the drive heads to
park.
4.
Use your hand to support the bottom of the drive, while you slowly pull the
drive straight out.
Do not allow the drive to fall.
5.
Place the drive in an electrostatic-protected container. Do not stack drives.