HP LH4r HP Netserver LH 3000 Installation Guide - Page 74

the slot will power on when the HP NetServer boots.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Chapter 6 Installing Additional PCI Boards Figure 6-4. Install Non-Hot-Plug Board 11. Align the board with its slot along its full length, and push it into the slot with even pressure along the top edge of the board until it is fully seated in its connector. NOTE To prevent EMI problems, ensure each unused PCI slot has a PCI slot cover. If a PCI board is removed and not re-installed, you must install a PCI slot cover. 12. Close the PCI hold-down latch, by reversing the procedure in step 9. NOTE Be sure the PCI hold-down latch closes fully (clicks) so that the slot will power on when the HP NetServer boots. 13. If the installed accessory board requires an external connection or a connection to the I/O board, ensure the cable is properly attached. Refer to the accessory board documentation for connection requirements. 14. Replace the front board hold-down. 66

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Chapter 6
Installing Additional PCI Boards
66
Figure 6-4. Install Non-Hot-Plug Board
11.
Align the board with its slot along its full length, and push it into the slot
with even pressure along the top edge of the board until it is fully seated in
its connector.
NOTE
To prevent EMI problems, ensure each unused PCI slot has a
PCI slot cover. If a PCI board is removed and not re-installed,
you must install a PCI slot cover.
12.
Close the PCI hold-down latch, by reversing the procedure in step 9.
NOTE
Be sure the PCI hold-down latch closes fully (clicks) so that
the slot will power on when the HP NetServer boots.
13.
If the installed accessory board requires an external connection or a
connection to the I/O board, ensure the cable is properly attached.
Refer to the accessory board documentation for connection requirements.
14.
Replace the front board hold-down.