HP LH4r HP Netserver LH 3000 Installation Guide - Page 59

Controls, Ports, and Indicators.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Chapter 4 Installing Mass Storage Devices Follow the setup steps in the exact order shown below for a successful installation. Skip any steps that do not apply to your installation. 1. Log off all users and gracefully shut down the network operating system according to directions in your NOS documentation. 2. Power down the HP NetServer according to the instructions in Chapter 2, "Controls, Ports, and Indicators." 3. Disconnect the power cords and cables and, if necessary, label each one to support re-assembly. CAUTION The power supplies will continue to provide standby current to the NetServer until the power cable is disconnected. 4. For rack-mount and pedestal models, follow the instructions in Chapter 3, "Opening and Closing the HP NetServer," to gain access to the server. 5. Select an available shelf for the device and remove the filler panel. 6. If the device you are installing is the boot device, check the boot priority. 7. Install the device on a mass storage tray following the directions included with the tray. 8. Connect the cable from the power supply and the SE SCSI cable from the I/O board to the device. 9. Follow the procedure in Chapter 3, "Opening and Closing the HP NetServer," for closing up the server. 10. Reconnect power and cables. 11. Configure the drive according to steps in Chapter 10, "Configuring the HP NetServer." Restore the HP NetServer to normal operation. This completes your non-hot-swap mass storage installation. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Chapter 4
Installing Mass Storage Devices
51
Follow the setup steps in the exact order shown below for a successful installation.
Skip any steps that do not apply to your installation.
1.
Log off all users and gracefully shut down the network operating system
according to directions in your NOS documentation.
2.
Power down the HP NetServer according to the instructions in Chapter 2,
"Controls, Ports, and Indicators."
3.
Disconnect the power cords and cables and, if necessary, label each one to
support re-assembly.
CAUTION
The power supplies will continue to provide standby current to
the NetServer until the power cable is disconnected.
4.
For rack-mount and pedestal models, follow the instructions in Chapter 3,
"Opening and Closing the HP NetServer," to gain access to the server.
5.
Select an available shelf for the device and remove the filler panel.
6.
If the device you are installing is the boot device, check the boot priority.
7.
Install the device on a mass storage tray following the directions included
with the tray.
8.
Connect the cable from the power supply and the SE SCSI cable from the
I/O board to the device.
9.
Follow the procedure in Chapter 3, "Opening and Closing the HP
NetServer," for closing up the server.
10.
Reconnect power and cables.
11.
Configure the drive according to steps in Chapter 10, "Configuring the HP
NetServer."
Restore the HP NetServer to normal operation.
This completes your non-hot-swap mass storage installation.