HP LH4r HP Netserver LH 3000 Installation Guide - Page 135

Bootable Cards], 30 ID01 LUN0 HP, 26GB A], 30 ID02 LUN0 HP

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 135 highlights

Chapter 10 Configuring the HP NetServer boards) installed. The system attempts to boot the NOS on the first hard disk drive (or DAC or SCSI board) found in this list. If no NOS is found, the system tries the next hard drive in the list until a NOS is found. 1. [Bootable Cards] 2. [#30 ID01 LUN0 HP 3. [#30 ID02 LUN0 HP 4.26GB A] 4.26GB A] 6. Use the plus (+) or minus (-) keys to move the desired hard drive (or DAC or SCSI board) to the top of the list. ◊ The HD boot list has a maximum capacity of eight (8) logical drives. ◊ If a bootable Disk Array Controller (DAC) board is used, the RAID array is seen as a single logical drive. ◊ If more than eight logical drives are connected to the HP NetServer, drives 9 and above (including the DAC or SCSI boards and the drives connected to each) will not be recognized by the Setup Utility. ◊ You will not be able to enter the Setup Utility to make changes to these logical drives (including DACs and SCSI boards) during the boot process. ◊ However, these logical devices (including DACs and SCSI boards) will be properly recognized and activated by the respective NOS. ◊ For more information about selection guidelines, refer to Information Assistant on the HP NetServer Online Documentation CD-ROM. 7. Press Esc to exit the Hard Drive menu. 8. Press Esc again to exit the Boot Settings menu. 9. Use the right-arrow key to select the Exit menu. 10. Choose "Exit Saving Changes" from the list of exit options, then press Enter. A dialog appears asking you to confirm your decision. 11. Choose "Yes" and press Enter. Then the HP NetServer reboots. 127

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Chapter 10
Configuring the HP NetServer
127
boards) installed. The system attempts to boot the NOS on the first hard
disk drive (or DAC or SCSI board) found in this list. If no NOS is found,
the system tries the next hard drive in the list until a NOS is found.
1. [Bootable Cards]
2. [#30 ID01 LUN0 HP
4.26GB A]
3. [#30 ID02 LUN0 HP
4.26GB A]
6.
Use the plus (+) or minus (-) keys to move the desired hard drive (or DAC
or SCSI board) to the top of the list.
◊
The HD boot list has a maximum capacity of eight (8) logical drives.
◊
If a bootable Disk Array Controller (DAC) board is used, the RAID
array is seen as a single logical drive.
◊
If more than eight logical drives are connected to the HP NetServer,
drives 9 and above (including the DAC or SCSI boards and the drives
connected to each) will not be recognized by the Setup Utility.
◊
You will not be able to enter the Setup Utility to make changes to these
logical drives (including DACs and SCSI boards) during the boot
process.
◊
However, these logical devices (including DACs and SCSI boards) will
be properly recognized and activated by the respective NOS.
◊
For more information about selection guidelines, refer to Information
Assistant on the
HP NetServer Online Documentation CD-ROM
.
7. Press
Esc
to exit the Hard Drive menu.
8. Press
Esc
again to exit the Boot Settings menu.
9.
Use the right-arrow key to select the
Exit
menu.
10.
Choose "Exit Saving Changes"
from the list of exit options, then press
Enter
.
A dialog appears asking you to confirm your decision.
11.
Choose "Yes" and press
Enter
.
Then the HP NetServer reboots.