HP LH4r HP Netserver LH 3000 Installation Guide - Page 159
Tighten both screws in the mounting flanges of the slide.
 |
View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 159 highlights
Chapter 13 Alternative Rack Mounting 17. Insert the slide fixed mounting flange between the column and bar nuts. Press the slide firmly against the front column (see Figure 13-6). 1. Insert mounting flange of slides between bar nut and rear side of column face. 2. Press slide tightly against column and tighten screws to hold slide in place. Figure 13-6. Securing the Slide to the Front Column NOTE The slide members cannot be removed. 18. Tighten both screws in the mounting flanges of the slide. 19. Insert the threaded stud on the rear of the slide into the rear column-mounting hole marked earlier. 20. Secure the slide with a hex nut and lock washer saved earlier. 21. Repeat steps 14 through 20 and install the second slide in the rack. 151
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154 -
155 -
156 -
157 -
158 -
159 -
160 -
161 -
162 -
163 -
164 -
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
 |
 |
Chapter 13
Alternative Rack Mounting
151
17.
Insert the slide fixed mounting flange between the column and bar nuts.
Press the slide firmly against the front column (see Figure 13-6).
1. Insert
mounting
flange of slides
between
bar nut and
rear side of
column face.
2. Press slide
tightly against
column and
tighten
screws to
hold slide
in place.
Figure 13-6. Securing the Slide to the Front Column
NOTE
The slide members cannot be removed.
18.
Tighten both screws in the mounting flanges of the slide.
19.
Insert the threaded stud on the rear of the slide into the rear
column-mounting hole marked earlier.
20.
Secure the slide with a hex nut and lock washer saved earlier.
21.
Repeat steps 14 through 20 and install the second slide in the rack.