HP SW TL881 DLT Mini-Lib/1 Compaq TL881 MiniLibrary System Users Guide (May 19 - Page 145

Ctl Firmware Error, DLT Timeout Error, Invalid Ctl Msg, in a Prevent Removal State.

Get HP SW TL881 DLT Mini-Lib/1 PDF manuals and user guides View all HP SW TL881 DLT Mini-Lib/1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 145 highlights

6-10 Compaq TL881 Minilibrary System Users Guide Table 6-2 Fault Symptom Codes continued Control Error Codes - 2xxx 200F Removal Prevented Medium removal was attempted when in a Prevent Removal State. 2010 Ctl Firmware Error An invalid configuration was detected. The configuration jumpers on the main board may not be set properly. 2011 Ctl Firmware Error A status block was received by the Control Process operating in a StandAlone or Slave configuration. Since commands are never sent in these modes, status cannot be received. 2012 Ctl Firmware Error A command was received which was invalid for the current configuration. 2013 Ctl Firmware Error 2014 Ctl Firmware Error 2015 Ctl Firmware Error 2016 Ctl Firmware Error 2030 DLT Timeout Error During powerup, communication with one of the DLT drives was unsuccessful. 2031 DLT Timeout Error While trying to update the front panel, communication with one of the DLT drives was unsuccessful. 2032 DLT Timeout Error Communication with DLT drive 1 was unsuccessful (sequential mode). 2033 DLT Timeout Error Communication with DLT drive 2 was unsuccessful (sequential mode). 2034 DLT Timeout Error While attempting to update the cartridge map, communication with one of the DLT drives was unsuccessful. 204x Invalid Ctl Msg An illegal message type code was received. This can be the result of receiving a NULL type code, a status code without a command being active, or a command code while a command is currently active. continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
6-10
Compaq TL881 Minilibrary System Users Guide
Table 6-2
Fault Symptom Codes
continued
Control Error Codes – 2xxx
200F
Removal Prevented
Medium removal was attempted when
in a Prevent Removal State.
2010
Ctl Firmware Error
An invalid configuration was detected.
The configuration jumpers on the main
board may not be set properly.
2011
Ctl Firmware Error
A status block was received by the
Control Process operating in a Stand-
Alone or Slave configuration.
Since
commands are never sent in these
modes, status cannot be received.
2012
Ctl Firmware Error
A command was received which was
invalid for the current configuration.
2013
Ctl Firmware Error
2014
Ctl Firmware Error
2015
Ctl Firmware Error
2016
Ctl Firmware Error
2030
DLT Timeout Error
During powerup, communication with
one of the DLT drives was
unsuccessful.
2031
DLT Timeout Error
While trying to update the front panel,
communication with one of the DLT
drives was unsuccessful.
2032
DLT Timeout Error
Communication with DLT drive 1 was
unsuccessful (sequential mode).
2033
DLT Timeout Error
Communication with DLT drive 2 was
unsuccessful (sequential mode).
2034
DLT Timeout Error
While attempting to update the
cartridge map, communication with
one of the DLT drives was
unsuccessful.
204x
Invalid Ctl Msg
An illegal message type code was
received.
This can be the result of
receiving a NULL type code, a status
code without a command being active,
or a command code while a command
is currently active.
continued