HP SW TL881 DLT Mini-Lib/1 Compaq TL881 MiniLibrary System Users Guide (May 19 - Page 183

Removing and, Replacing the Drive Caddy Assembly

Page 183 highlights

D-8 Compaq TL881 Minilibrary System Users Guide 5. Slide the drive (6) into the drive caddy assembly; position the drive so the threaded holes in the top and bottom of the drive are aligned with the screws holes. 6. Install the four 6-32 sems pan-head Phillips screws that were removed in Step 1. 7. Connect the unused connector on the power Y-cable to the drive just installed. 8. Connect the unused connector on the SCSI cable to the drive just installed. 9. Install the RS-422 cable supplied with the kit, sliding it under the clamps so that the connector is adjacent to the connector on top of the new drive. 10. Install the RS-422 cable removed in Step 3 over the top of the new RS422 cable so that the connector is adjacent to the connector on top of the original drive. 11. Connect the RS-422 cables to the connectors on the top of the drives, through the holes in the top of the drive caddy assembly. 12. Replace the drive caddy assembly as described in Removing and Replacing the Drive Caddy Assembly.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200

D-8
Compaq TL881 Minilibrary System Users Guide
5.
Slide the drive (6) into the drive caddy assembly; position the drive so
the threaded holes in the top and bottom of the drive are aligned with the
screws holes.
6.
Install the four 6-32 sems pan-head Phillips screws that were removed in
Step 1.
7.
Connect the unused connector on the power Y-cable to the drive just
installed.
8.
Connect the unused connector on the SCSI cable to the drive just
installed.
9.
Install the RS-422 cable supplied with the kit, sliding it under the
clamps so that the connector is adjacent to the connector on top of the
new drive.
10.
Install the RS-422 cable removed in Step 3 over the top of the new RS-
422 cable so that the connector is adjacent to the connector on top of the
original drive.
11.
Connect the RS-422 cables to the connectors on the top of the drives,
through the holes in the top of the drive caddy assembly.
12.
Replace the drive caddy assembly as described in
Removing and
Replacing the Drive Caddy Assembly
.