HP SW TL881 DLT Mini-Lib/1 Compaq TL881 MiniLibrary System Users Guide (May 19 - Page 146

Message, Description, Power Down, Wait 30 seconds, Power

Get HP SW TL881 DLT Mini-Lib/1 PDF manuals and user guides View all HP SW TL881 DLT Mini-Lib/1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 146 highlights

Table 6-2 Fault Symptom Codes continued FSC Message 205x No Free Queues 206x Calib. Error Port x 206f Pass-thru Init Error 2070 Command Timeout 2071 2072 Command Timeout Command Timeout 2073 Drive Config Error 2074 Stow Error 2075 Fetch Error Diagnostics and Troubleshooting 6-11 Description The system could not allocate a free queue. When trying to locate the unit attached to port x, the pass-thru elevator reached the top of rail. The pass-thru elevator did not travel a minimum distance to reach the top of its travel. Enter to reboot. The ten minute timer was exceeded when trying to fetch from a drive. Internal error only. Not reported to the operator or host. Power Down, Wait 30 seconds, Power Up. Occurs if the power is cycled too quickly and the DLT drive comes up in an error state and doesn't communicate with the library controller. Set if the Alternate Unload has not been selected. This currently applies only to DLT7000's with a controller microcode revision greater than 50. A stow timeout error has occurred when accessing a remote unit. Press Enter to Reboot for orphan cartridge recovery. During a remote fetch operation, the remote unit returned an error. continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
Diagnostics and Troubleshooting
6-11
Table 6-2
Fault Symptom Codes
continued
FSC
Message
Description
205x
No Free Queues
The system could not allocate a free
queue.
206x
Calib. Error Port x
When trying to locate the unit attached
to port x, the pass-thru elevator
reached the top of rail.
206f
Pass-thru Init Error
The pass-thru elevator did not travel a
minimum distance to reach the top of
its travel.
2070
Command Timeout
Enter to reboot.
The ten minute timer
was exceeded when trying to fetch
from a drive.
2071
Command Timeout
Internal error only.
Not reported to the
operator or host.
2072
Command Timeout
Power Down, Wait 30 seconds, Power
Up.
Occurs if the power is cycled too
quickly and the DLT drive comes up in
an error state and doesn’t
communicate with the library
controller.
2073
Drive Config Error
Set if the Alternate Unload has not
been selected.
This currently applies
only to DLT7000’s with a controller
microcode revision greater than 50.
2074
Stow Error
A stow timeout error has occurred
when accessing a remote unit.
Press
Enter to Reboot for orphan cartridge
recovery.
2075
Fetch Error
During a remote fetch operation, the
remote unit returned an error.
continued