HP SW TL881 DLT Mini-Lib/1 Compaq TL881 MiniLibrary System Users Guide (May 19 - Page 86

Rackmounting in a StorageWorks SW500, SW600, or SW800

Get HP SW TL881 DLT Mini-Lib/1 PDF manuals and user guides View all HP SW TL881 DLT Mini-Lib/1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

Installation 3-17 NOTES: All of the screws, washers, nutplates and/or metric conversion brackets required for rackmounting in either cabinet type are supplied with the Expansion Unit and MiniLibrary Base Module. You will need a #2 Phillips screwdriver and a flathead screwdriver. The left and right slides are alike, so there is no risk of confusing the parts on reassembly. The front of the cabinet, and front rails in this text refers to where the module face will be exposed (typically opposite from the main power source location). The main power source location thus becomes the rear of the cabinet, and where the rear rails exist. 4. Loosely assemble a mounting bracket to each outer slide, using two 1032 screws with washers and a nutplate for each. Select slots in the mounting brackets so the length of the assembly equals the distance between the front and rear rails of the rack. 5. Locate the screw holes in the front and rear rails of the cabinet or equipment rack where the drive is to be installed. CAUTION: The cooling fan at the rear of the drive must not be obstructed when the drive is installed in the rack. It is advisable to allow two inches of clearance behind the rear panel of the module. 6. From this point, the instructions vary depending on cabinet type, and you should proceed as follows: q Refer to the Compaq Rackmounting Template, which is included with each module. q EIA/RETMA Cabinet Rackmounting - Refer to the section entitled Rackmounting in a Standard (19") EIA/RETMA Cabinet q StorageWorks Metric Rackmounting - Refer to the section entitled Rackmounting in a StorageWorks (SW500, SW600, or SW800) Metric Cabinet

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
Installation
3-17
NOTES:
All of the screws, washers, nutplates and/or metric conversion brackets required
for rackmounting in either cabinet type are supplied with the Expansion Unit and
MiniLibrary Base Module.
You will need a #2 Phillips screwdriver and a flathead
screwdriver.
The left and right slides are alike, so there is no risk of confusing the parts on reassembly.
The
front of the cabinet, and front rails
in this text refers to where the
module face
will be
exposed (typically opposite from the main power source location). The main power source
location thus becomes the
rear of the cabinet
, and where the
rear rails
exist.
4.
Loosely assemble a mounting bracket to each outer slide, using two 10-
32 screws with washers and a nutplate for each. Select slots in the
mounting brackets so the length of the assembly equals the distance
between the front and rear rails of the rack.
5.
Locate the screw holes in the front and rear rails of the cabinet or
equipment rack where the drive is to be installed.
CAUTION:
The cooling fan at the rear of the drive must not be obstructed when
the drive is installed in the rack. It is advisable to allow two inches of clearance
behind the rear panel of the module.
6.
From this point, the instructions vary depending on cabinet type, and
you should proceed as follows:
q
Refer to the Compaq Rackmounting Template, which is included
with each module.
q
EIA/RETMA Cabinet Rackmounting - Refer to the section entitled
Rackmounting in a Standard (19”) EIA/RETMA Cabinet
q
StorageWorks Metric Rackmounting - Refer to the section entitled
Rackmounting in a StorageWorks (SW500, SW600, or SW800)
Metric Cabinet