HP SW TL881 DLT Mini-Lib/1 Compaq TL881 MiniLibrary System Users Guide (May 19 - Page 76

Assembling the Pass-Thru Mechanism, Mechanical

Get HP SW TL881 DLT Mini-Lib/1 PDF manuals and user guides View all HP SW TL881 DLT Mini-Lib/1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Installation 3-7 mechanism. The height is equal to the height of the stack of modules in your system plus any gaps you intend to include in the stack. Use the following procedure to assemble your Pass-Thru mechanism. Assembling the Pass-Thru Mechanism In most cases, you have received a pre-assembled Pass-Thru mechanism. If its length is correct for your system, turn to the section entitled Mechanical Installation of the Expansion and MiniLibrary Base Modules and continue on to the end of the chapter. If you need to add sections, please take a few minutes to read this section and the section entitled Installing the Belt, before proceeding to Adding to an Existing Pass-Thru Mechanism. NOTE: References to left and right refer to the position of the part when the Pass-Thru mechanism is assembled and mounted in the rack, as viewed from the front of the rack. Refer to Figures 3-1 and 3-4. 1. Place the base section, with the inside facing down, overhanging the right end of the work area, with the bottom plate of the section toward the right. 2. Place each of the extension sections, with the inside facing down, in a row aligned edge-to-edge beginning with the base section. The bottoms of the sections should be toward the right. Omit the motor drive at this time. 3. Center one of the support braces across the rear of the base section over the holes on the rear surface of that section. 4. Insert two M4 x 20 Phillips sems screws through the holes in the support brace into the holes in the base section, and tighten.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
Installation
3-7
mechanism. The height is equal to the height of the stack of modules in your
system plus any gaps you intend to include in the stack. Use the following
procedure to assemble your Pass-Thru mechanism.
Assembling the Pass-Thru Mechanism
In most cases, you have received a pre-assembled Pass-Thru mechanism. If its
length is correct for your system, turn to the section entitled
Mechanical
Installation of the Expansion and MiniLibrary Base Modules
and continue on
to the end of the chapter. If you need to add sections, please take a few
minutes to read this section and the section entitled
Installing the Belt
, before
proceeding to
Adding to an Existing Pass-Thru Mechanism.
NOTE:
References to left and right refer to the position of the part when the Pass-Thru
mechanism is assembled and mounted in the rack, as viewed from the front of the rack.
Refer to Figures 3-1 and 3-4.
1.
Place the base section, with the inside facing down, overhanging the
right end of the work area, with the bottom plate of the section toward
the right.
2.
Place each of the extension sections, with the inside facing down, in a
row aligned edge-to-edge beginning with the base section. The bottoms
of the sections should be toward the right. Omit the motor drive at this
time.
3.
Center one of the support braces across the rear of the base section over
the holes on the rear surface of that section.
4.
Insert two M4 x 20 Phillips sems screws through the holes in the support
brace into the holes in the base section, and tighten.